Product List
Tel: 0086-13598879167
Fax: 0086-371-88884766
Email: admin@gangsteel.com
Skype: gangsteel001@hotmail.com
Address: Gelin international Building,Zhengzhou city,Henan Province,China
SHS 110*110*6MM,S355J2H Square Pipe,S355J2H hollow sections,S355J2H
Adopt standard: S355J2H steel EN10210-1
The number of this European Standard(EN 10210)
The symbol S is structural steel, 275 for the minimum yield strength in thickness not greater than 16mm.
The Symbol J and number 0 or 2 mean for the qualities with specified impact properties at 0℃and -20℃respectively.
The capital letter H indicates hollow sections.
About S355J2H detail information，please consult technical date in following.
S355J2H The Chemical composition –Ladle analysis for product thickness≤65mm
|
Designation |
Type of deoxidation |
Sub Grop |
C % max. Nominal thickness(mm) |
Si % max.
|
Mn % max.
|
P % max.
|
S % max.
|
N % max.
|
||
|
According to EN 10027-1 and IC 10 |
According to EN 10027-2 |
≤40 |
>40 ≤65 |
|||||||
|
S355J2H |
1.0576 |
FF |
QS |
0.22 |
0.22 |
0.55 |
1.60 |
0.035 |
0.035 |
- |
1)The deoxidation methods are designated as follows:
FF-Full killed steel containing nitrogen binding elements in amounts sufficient to bind available nitrogen (e.g. min. 0.020% total Al, or 0.015% soluble Al).
2)QS-quality steel.
3)It is permissible to exceed the specified values provided that for each increase of 0.001%N the P max content will be reduced by 0.005%,the N content of the ladle analysis ,however,shall not be more than 0.012%
4)The max. value for nitrogen does not apply if the chemical composition shows a minimum total Al content of 0.020% with a minimum AL/N ratio of 2:1, or if sufficient other N-binding elements are present. The N-binding elements shall be recorded in Inspection Document.
S355J2H Mechanical properties for non-alloy structural steel hollow section
|
Designation |
Minimum yield strength REhin N/mm2 |
Tensile strength Rmin N/mm2 |
Minimum percentage elongation L0-5,65√S0 |
Impact properties |
||||||||
|
According to EN 10027-1 and IC 10 |
According to EN 10027-2 |
Nominal thickness in mm |
Nominal thickness in mm |
Longitudinal |
Transverse |
Test temperature |
Minimum average absorbed energy(J)for standard test pieces |
|||||
|
≤16 |
>16 ≤40 |
>40 ≤65 |
<3
|
≥ 3≤65 |
Nominal thickness in mm |
|||||||
|
≤40 |
>40 ≤65 |
≤40 |
>40 ≤65 |
|||||||||
|
S355J2H |
1.0576 |
355 |
345 |
335 |
510-680 |
490-630 |
22 |
21 |
20 |
19 |
-20 |
27 |
Production Size:
|
Square Pipe |
|
Square Pipe |
||||
|
Size |
Thick |
Length |
|
Size |
Thick |
Length |
|
mm |
mm |
Meters |
|
mm |
mm |
Meters |
|
500*500mm |
8-25mm |
3m-12m |
|
300*300mm |
8-25mm |
3m-12m |
|
220*220mm |
8-25mm |
3m-12m |
|
150*150mm |
5-14mm |
3m-12m |
|
130*130mm |
4-12mm |
3m-12m |
|
80*80mm |
4-12mm |
3m-12m |
|
450*450mm |
8-25mm |
3m-12m |
|
280*280mm |
8-25mm |
3m-12m |
|
200*200mm |
8-25mm |
3m-12m |
|
140*140mm |
4-14mm |
3m-12m |
|
120*120mm |
4-12mm |
3m-12m |
|
60*60mm |
4-12mm |
3m-12m |
|
400*400mm |
8-25mm |
3m-12m |
|
250*250mm |
8-25mm |
3m-12m |
|
180*180mm |
7-20mm |
3m-12m |
|
135*135mm |
4-14mm |
3m-12m |
|
110*110mm |
4-12mm |
3m-12m |
|
50*50mm |
4-12mm |
3m-12m |
|
350*350mm |
8-25mm |
3m-12m |
|
40*40mm |
4-10mm |
3m-12m |
|
160*160mm |
5-16mm |
3m-12m |
|
30*30mm |
3-6mm |
3m-12m |
|
100*100mm |
4-12mm |
3m-12m |
|
20*20mm |
2-4mm |
3m-12m |
For more information in quality certificate or inquiry in competitive official quotation, please contact us by email or calling.
GANGSTEEL Galvanized Coil Steel Stock List and Price 2016-02-25
The tension was high as Gregoire Parenty and Martin Lindqvist took the stage to announce the winner of the 2015
EN10025-5 S355J0WP,S355J2WP,S355J0W,S355J2W steel plate
DIN 17155 HII | HII steel plate DIN standard HII pressure vessel steel has now been superseded with the Euro No
