Q235B equal-leg and unequal-leg angles are combined here because both are solid hot-rolled L-sections using the same material specification and the angle families in GB/T 706. They differ in geometry and connection behaviour, not in the meaning of Q235B. Keeping their complete dimension tables together allows a buyer to compare legs and thickness without treating each length ratio as a new material product.

Specify the full leg dimensions and nominal leg thickness. An equal angle 100 × 100 × 10 is not interchangeable with an unequal angle 150 × 90 × 10 simply because both have 10 mm legs. The connected leg, bolt line and free-leg projection affect tension efficiency and compression stability; theoretical mass alone does not measure usable member capacity.

Order identity: keep material and section standards separate
Order fieldScope
ProductQ235B equal and unequal steel angles
Material standardGB/T 700-2006
Section/product standardGB/T 706: shape series, dimensions, tolerances and rolled-product requirements; numerical basis here 2016
Delivery conditionHot rolled; no normalized or TMCP route implied
CertificationIdentify grade, heat/batch traceability, dimensional edition and agreed test reporting

The numerical size tables on this page use GB/T 706-2016. On 22 November 2026 this is the effective edition. GB/T 706-2026 has been issued but does not take effect until 1 December 2026. These are not 2026-edition dimension tables. Specify the contractual dimensional edition, including its tolerances and mass basis, rather than silently applying a later edition to an earlier catalogue.

GB equal angle100 by100 by10 and unequal angle150 by90 by10 drawn to one scale, showing leg dimensions, 12 mm root and one-third-thickness toe radii
GB equal angle100 by100 by10 and unequal angle150 by90 by10 drawn to one scale, showing leg dimensions, 12 mm root and one-third-thickness toe radii. Fillet and toe radii are roll-pass-design references, not independent delivery acceptance criteria.

Selection and connection engineering

Choose the connected leg before comparing unequal angles

An unequal angle has a long leg B and a short leg b. Connecting through the long leg rather than the short leg changes the bolt platform, eccentricity and free-leg projection. State the orientation on the drawing and check edge distance, pitch, root clearance and access. The catalogue designation alone does not identify which leg carries the bolts.

Check net section and shear lag for single-leg tension

A single-leg bolted angle is not uniformly loaded through its centroid. The design may need effective net-area or shear-lag provisions in addition to gross-section yield, with bolt holes, block tearing and connection length checked under the project code. Raising the gross area does not repair an inadequate end detail. A weld connected along one leg also needs an explicit load path.

Use the appropriate axis for compression bracing

The weakest principal axis of an angle is generally not the geometric axis parallel to a leg. Equal-leg angles have a symmetry bisector; unequal angles require their own principal-axis properties. The outstanding leg, connection eccentricity and end restraint can influence compression buckling. Do not estimate bracing resistance from a rectangular leg-width calculation or from an EN angle of apparently identical nominal size.

Retain the GB radius and mass convention

The reference equal angle100 × 100 × 10 has A = 19.26 cm² and a tabulated mass of 15.1 kg/m. The unequal angle150 × 90 × 10 is 18.3 kg/m. Root and toe geometry differ from some EN reference sections. Do not overwrite the GB mass or usable root clearance with a European catalogue merely because the printed leg dimensions match.

Mechanical properties: identify the tested thickness

Q235B section material: thickness bands covering every listed section
Nominal material thicknessMinimum ReH, MPaRm, MPaMinimum A, %
d ≤16 mm235370–50026
16 < d ≤40 mm225370–50026

For these tables d denotes the applicable material-thickness reference: ordinarily the web in I-sections/channels and the leg in angles. It is not the overall height or leg width. Elongation values are the section/bar longitudinal reference; plate-specific specimen orientation or deductions must not be imported unchanged. Final specimen position, direction and preparation follow the ordered standards and contract, including GB/T 2975. These two bands cover the supplied reference series; they do not authorize other heavy-section products.

The angle leg thickness d is the ordinary material reference. The largest listed leg is 35 mm, so the series spans the first two yield bands but not the >40 mm band. Widths such as 200 or 250 mm do not select the material thickness band. Unequal leg widths do not imply unequal leg thicknesses.

Q235B impact quality, subject to test applicability
TemperatureLongitudinal Charpy V-notch referenceThickness and reporting qualification
+20 °C27 JOrdinary section test obligation starts at nominal thickness 12 mm; supplier-guaranteed omission below 25 mm requires buyer agreement.

Apply the 12 mm trigger to the leg thickness, not to the long-leg width. Many of the small angles are below that trigger. The B suffix is not proof that every delivered certificate contains measured impact results. Specify actual impact testing if required; use the standard’s applicable specimen and acceptance rules rather than assuming full-size specimens can be obtained from every section. B at +20 °C is not a subzero toughness qualification.

Heat chemistry and finished-product analysis

Material heat/ladle analysis: maxima in mass % unless stated otherwise
ElementLimitAcceptance note
C0.20A rise to 0.22 requires purchaser agreement; there is no carbon minimum in this edition.
Si0.35Heat-analysis maximum.
Mn1.40Maximum; do not impose the obsolete 0.30–0.70 range as the 2006 requirement.
P0.045Heat-analysis maximum.
S0.045Heat-analysis maximum.
Cr / Ni / Cu, each0.30Residual limits; analysis may be omitted when the supplier guarantees compliance.
N0.008Subject to the standard’s nitrogen/phosphorus compensation and nitrogen-binding exceptions; identify any applicable exception.
As0.080Ordinary maximum; arsenic-bearing ore arrangements require agreement.

These are material heat/ladle limits under GB/T 700-2006, not a finished-product analysis tolerance table. Q235B has no universal CEV ceiling in that standard. Where welding assessment requires carbon equivalent, agree the calculation and acceptance criterion using the actual heat chemistry rather than inventing a grade-wide cap.

Keep heat analysis and product analysis distinct. Heat/ladle results identify the melt; a test on the finished rolled section is product analysis and is assessed using the applicable GB/T 222 permitted-deviation provisions. No numerical product-analysis deviations are supplied by the compiled dataset, so no extra tolerance has been invented here. If product analysis is required, agree the sampling, test method, material edition and deviation table before ordering; do not add a discretionary percentage to every heat limit.

GB/T 706-2016 dimensions and theoretical mass

All dimensions are millimetres; A is cross-sectional area in cm² and mass is kg/m. The values are a reference series, not a stock list or a guarantee that every size/grade combination can be supplied on a particular enquiry. Confirm the actual section, length, quantity and certification requirement. The tabulated mass is retained on its published 2016 basis rather than reconstructed from rounded area values. Dimensional, shape and mass tolerances must be taken from the contracted edition, not from the number of decimal places below.

Equal-leg dimensions use b × b × d. Unequal-leg dimensions use B × b × d, with B the long leg and b the short leg. Both legs have the same nominal thickness d in this scope. The yield column uses that leg thickness; the dimensions are not EN 10056 or JIS dimensions relabelled as GB.

Equal-leg angles, 115 rows; GB/T 706-2016 reference
Modelb × b × db mmd mmA cm²kg/mLeg-band ReH min, MPa
220×20×32031.1320.89235
220×20×42041.4591.15235
2.525×25×32531.4321.12235
2.525×25×42541.8591.46235
330×30×33031.7491.37235
330×30×43042.2761.79235
3.636×36×33632.1091.66235
3.636×36×43642.7562.16235
3.636×36×53653.3822.65235
440×40×34032.3591.85235
440×40×44043.0862.42235
440×40×54053.7922.98235
4.545×45×34532.6592.09235
4.545×45×44543.4862.74235
4.545×45×54554.2923.37235
4.545×45×64565.0773.99235
550×50×35032.9712.33235
550×50×45043.8973.06235
550×50×55054.8033.77235
550×50×65065.6884.46235
5.656×56×35633.3432.62235
5.656×56×45644.393.45235
5.656×56×55655.4154.25235
5.656×56×65666.425.04235
5.656×56×75677.4045.81235
5.656×56×85688.3676.57235
660×60×56055.8294.58235
660×60×66066.9145.43235
660×60×76077.9776.26235
660×60×86089.027.08235
6.363×63×46344.9783.91235
6.363×63×56356.1434.82235
6.363×63×66367.2885.72235
6.363×63×76378.4126.60235
6.363×63×86389.5157.47235
6.363×63×10631011.669.15235
770×70×47045.5704.37235
770×70×57056.8765.40235
770×70×67068.1606.41235
770×70×77079.4247.40235
770×70×870810.678.37235
7.575×75×57557.4125.82235
7.575×75×67568.7976.91235
7.575×75×775710.167.98235
7.575×75×875811.509.03235
7.575×75×975912.8310.1235
7.575×75×10751014.1311.1235
880×80×58057.9126.21235
880×80×68069.3977.38235
880×80×780710.868.53235
880×80×880812.309.66235
880×80×980913.7310.8235
880×80×10801015.1311.9235
990×90×690610.648.35235
990×90×790712.309.66235
990×90×890813.9410.9235
990×90×990915.5712.2235
990×90×10901017.1713.5235
990×90×12901220.3115.9235
10100×100×6100611.939.37235
10100×100×7100713.8010.8235
10100×100×8100815.6412.3235
10100×100×9100917.4613.7235
10100×100×101001019.2615.1235
10100×100×121001222.8017.9235
10100×100×141001426.2620.6235
10100×100×161001629.6323.3235
11110×110×7110715.2011.9235
11110×110×8110817.2413.5235
11110×110×101101021.2616.7235
11110×110×121101225.2019.8235
11110×110×141101429.0622.8235
12.5125×125×8125819.7515.5235
12.5125×125×101251024.3719.1235
12.5125×125×121251228.9122.7235
12.5125×125×141251433.3726.2235
12.5125×125×161251637.7429.6235
14140×140×101401027.3721.5235
14140×140×121401232.5125.5235
14140×140×141401437.5729.5235
14140×140×161401642.5433.4235
15150×150×8150823.7518.6235
15150×150×101501029.3723.1235
15150×150×121501234.9127.4235
15150×150×141501440.3731.7235
15150×150×151501543.0633.8235
15150×150×161501645.7435.9235
16160×160×101601031.5024.7235
16160×160×121601237.4429.4235
16160×160×141601443.3034.0235
16160×160×161601649.0738.5235
18180×180×121801242.2433.2235
18180×180×141801448.9038.4235
18180×180×161801655.4743.5235
18180×180×181801861.9648.6225
20200×200×142001454.6442.9235
20200×200×162001662.0148.7235
20200×200×182001869.3054.4225
20200×200×202002076.5160.1225
20200×200×242002490.6671.2225
22220×220×162201668.6753.9235
22220×220×182201876.7560.3225
22220×220×202202084.7666.5225
22220×220×222202292.6872.8225
22220×220×2422024100.578.9225
22220×220×2622026108.385.0225
25250×250×182501887.8469.0225
25250×250×202502097.0576.2225
25250×250×2225022106.283.3225
25250×250×2425024115.290.4225
25250×250×2625026124.297.5225
25250×250×2825028133.0104225
25250×250×3025030141.8111225
25250×250×3225032150.5118225
25250×250×3525035163.4128225
Unequal-leg angles, 71 rows; GB/T 706-2016 reference
ModelB × b × dB mmb mmd mmA cm²kg/mLeg-band ReH min, MPa
2.5/1.625×16×3251631.1520.91235
2.5/1.625×16×4251641.4991.18235
3.2/232×20×3322031.4921.17235
3.2/232×20×4322041.9391.52235
4/2.540×25×3402531.8901.48235
4/2.540×25×4402542.4671.94235
4.5/2.845×28×3452832.1491.69235
4.5/2.845×28×4452842.8062.20235
5/3.250×32×3503232.4311.91235
5/3.250×32×4503243.1772.49235
5.6/3.656×36×3563632.7432.15235
5.6/3.656×36×4563643.5902.82235
5.6/3.656×36×5563654.4153.47235
6.3/465×40×4654044.0583.19235
6.3/465×40×5654054.9933.92235
6.3/465×40×6654065.9084.64235
6.3/465×40×7654076.8025.34235
7/4.570×45×4704544.5533.57235
7/4.570×45×5704555.6094.40235
7/4.570×45×6704566.6445.22235
7/4.570×45×7704577.6586.01235
7.5/575×50×5755056.1364.81235
7.5/575×50×6755067.2605.70235
7.5/575×50×8755089.4677.43235
7.5/575×50×1075501011.599.10235
8/580×50×5805056.3765.00235
8/580×50×6805067.5605.93235
8/580×50×7805078.7246.85235
8/580×50×8805089.8677.75235
9/5.690×56×5905657.2125.66235
9/5.690×56×6905668.5576.72235
9/5.690×56×7905679.8807.76235
9/5.690×56×89056811.188.78235
10/6.3100×63×61006369.6187.55235
10/6.3100×63×710063711.118.72235
10/6.3100×63×810063812.589.88235
10/6.3100×63×10100631015.4712.1235
10/8100×80×610080610.648.35235
10/8100×80×710080712.309.66235
10/8100×80×810080813.9410.9235
10/8100×80×10100801017.1713.5235
11/7110×70×611070610.648.35235
11/7110×70×711070712.309.66235
11/7110×70×811070813.9410.9235
11/7110×70×10110701017.1713.5235
12.5/8125×80×712580714.1011.1235
12.5/8125×80×812580815.9912.6235
12.5/8125×80×10125801019.7115.5235
12.5/8125×80×12125801223.3518.3235
14/9140×90×814090818.0414.2235
14/9140×90×10140901022.2617.5235
14/9140×90×12140901226.4020.7235
14/9140×90×14140901430.4623.9235
15/9150×90×815090818.8414.8235
15/9150×90×10150901023.2618.3235
15/9150×90×12150901227.6021.7235
15/9150×90×14150901431.8625.0235
15/9150×90×15150901533.9526.7235
15/9150×90×16150901636.0328.3235
16/10160×100×101601001025.3219.9235
16/10160×100×121601001230.0523.6235
16/10160×100×141601001434.7127.2235
16/10160×100×161601001639.2830.8235
18/11180×110×101801101028.3722.3235
18/11180×110×121801101233.7126.5235
18/11180×110×141801101438.9730.6235
18/11180×110×161801101644.1434.6235
20/12.5200×125×122001251237.9129.8235
20/12.5200×125×142001251443.8734.4235
20/12.5200×125×162001251649.7439.0235
20/12.5200×125×182001251855.5343.6225

Inspection, traceability and enquiry

Check both leg widths, leg thickness, squareness, straightness and twist. Identify the long/short leg orientation for unequal-angle connections. Reference fillet radii do not replace the delivery conditions in the applicable product standard.

  • State the full designation, exact grade/material edition, dimensional edition, lengths and quantity; identify any approved deviation from the normal hot-rolled scope.
  • Define the documentary requirement before ordering: heat analysis, applicable tensile results, the impact-test regime where required, and traceability between the certificate and supplied bundles. Do not assume a particular third-party certificate or inspection service.
  • Specify theoretical or actual-mass settlement and any special dimensional acceptance before quotation. Extra tests, coatings, fabrication or additional delivery conditions are not implied by a general grade enquiry.

Lead time: a typical mill order is about 35 days. Stocked sizes: 1–3 days, subject to enquiry and confirmation of the individual size, grade, quantity and delivery requirement. A tabulated section is not a statement that it is held in stock.

Related section and material comparisons

For a different rolled geometry in the same material, see Q235B H-beams. The Q235B plate material page is a separate product form: it must not replace the section-specific sampling and shape requirements above.

See the hot-rolled angle family overview and S235JR EN equal/unequal angles for other angle references. Confirm the material and dimension systems independently; matching printed legs do not establish equal mass or interchangeable properties.

Compare this GB/T 706 equal and unequal angle family in the other grade: Q355B Angles.

Frequently asked questions

Why are equal and unequal angles on one grade page?

They share the Q-grade material framework and the GB/T 706 angle product family. Separate equal- and unequal-leg dimension tables make the geometry clear without multiplying near-identical material pages. An unequal-leg enquiry still needs both leg sizes and its connected-leg orientation; the combined page is not a statement that the shapes are interchangeable.

Which dimension controls the material thickness band?

Use the nominal leg thickness d for the ordinary angle reference, not the long or short leg width. The sample location and preparation follow the applicable GB/T 2975 requirements. This scope is for equal thickness in both legs, not a special unequal-thickness marine section.

Does a one-leg connection develop the full gross-area strength?

Not automatically. Check the net section, load eccentricity, shear lag or effective-area provisions, bolt-group layout and block tearing under the project code. A load introduced through one leg is not distributed in the same way as a concentric tensile test on a material specimen.

Can the GB table mass be replaced by an EN angle mass?

No. Even at the same nominal leg sizes, root and toe conventions and tabulated rounding can differ. GB100 × 100 × 10 is tabulated at 15.1 kg/m on this basis. Use the ordered GB edition for theoretical-mass settlement and the actual specified section for structural properties, not a visually similar EN catalogue row.

Does Q235B always mean 235 MPa and a measured 27 J test?

No. Yield depends on the applicable material thickness; it is 235 MPa up to 16 mm and 225 MPa over 16 through 40 mm for the reference range here. The 27 J value is a +20 °C longitudinal impact requirement when the test regime applies. Thickness triggers and agreed supplier-guaranteed omissions must be considered before interpreting a certificate.

What if a finished-product chemistry test differs from the heat analysis?

First identify whether the result is a heat analysis or product analysis and which material edition and test method apply. Finished-product results use the applicable GB/T 222 permitted deviations; do not reject or accept them by silently adding a made-up allowance to the ladle table. Record the sampling and agreed acceptance basis before testing.

Can this grade be used in a welded or cold-service structure?

Neither application should be approved from the grade name alone. Welding needs actual heat chemistry, joint thickness, restraint and a suitable procedure; GB/T 700 does not supply a universal Q235B CEV ceiling. B quality is a room-temperature impact regime, not a subzero service guarantee. The project specification must set any additional toughness requirement.

What information should accompany a size enquiry?

Send the full section designation and variant, Q235B to GB/T 700-2006, the chosen GB/T 706 dimensional edition, lengths, quantity, mass-settlement basis and certificate/test requirements. Identify any actual impact testing or product analysis required. Typical mill orders are about 35 days; stocked sizes are 1–3 days only after the individual enquiry is confirmed.

For an enquiry to Gangsteel, provide the exact section and material specification, rather than a grade name alone. Quote acceptance remains subject to confirmation of the requested size, quantity and test scope.

Other Products