BV F460 steel plate, also written as BV/F460, BV Grade F460 or market names such as FH46 / FQ47, is the extra-high-strength hull structural steel of Bureau Veritas Rules for the Classification of Steel Ships (IACS UR W16 extra-high-strength family) with 460 MPa minimum yield, 570-720 MPa tensile strength and Charpy V-notch toughness at -60°C [-76°F]. In the grade name, "F" is the toughness class, and "460" is the yield-strength level in MPa (not AH460). Gangsteel, a steel plate exporter, supplies BV F460 plates cut to size for shipbuilding, offshore platforms and marine structures.

Data source: Per IACS UR W16 (extra-high-strength hull structural steel) as adopted in Bureau Veritas hull structural steel rules, cross-checked with LR FH46 / ABS FQ47 sibling pages on gangsteel.net. Official mill/certificate grade is BV F460. Verify the current BV edition before ordering.

BV F460 Chemical Composition (Heat Analysis)

 

ElementCMnSiPSAl (acid sol.)
BV F460, %0.18 max1.60 max0.10-0.550.025 max0.025 max0.015 min
ElementNNbVTiBNotes
BV F460, %0.020 max0.02-0.050.04-0.100.02 max0.005 maxNi/Cu/Cr/Mo per delivery condition (N/TM/QT) in UR W16

Per IACS UR W16 / Bureau Veritas extra-high-strength rules. Exact maxima for Ni, Cu, Cr and Mo depend on delivery condition (N/NR, TM or QT). Carbon equivalent / CET / Pcm limits apply by thickness and condition; confirm on the mill certificate and current rule edition.

Product Analysis (Check Analysis)

 

When product analysis is required, apply ASTM A6/A6M Table A permitted variations to the heat limits unless the element is min-only or not listed in Table A.

ElementHeat analysis limitProduct analysis (heat ± A6)
C0.18 max0.22 max
Mn1.60 maxsee A6 Table A vs heat upper limit
Si0.10-0.550.05–0.61 (approx. A6)
P0.025 max0.035 max
S0.025 max0.035 max
Al (acid sol.)0.015 minno A6 Table A tolerance; product value not tabulated
N0.020 max0.025 max (typical A6 +0.005)
Nb0.02-0.050.010–0.060
V0.04-0.100.030–0.110
Ti0.02 max0.03 max
B0.005 maxproduct analysis often not applicable

Product analysis applies only when specified; for a range, results may not vary both above and below it.

BV F460 Mechanical Properties

 

GradeYield strength, minTensile strengthElongation, min
BV F460460 MPa [67 ksi]570-720 MPa [83-104 ksi]17%

Per IACS UR W16 / Bureau Veritas rules (common t≤50 mm values). Yield may step down for thicker plates per UR W16; confirm thickness-dependent values on the order.

Charpy V-Notch Impact Requirements (-60°C [-76°F])

 

ThicknessTest temperatureLongitudinal, avg minTransverse, avg min
t≤50 mm-60°C [-76°F]46 J31 J
50<t≤70 mm-60°C [-76°F]46 J31 J
70<t≤100 mm-60°C [-76°F]46 J31 J

Per IACS UR W16 / Bureau Veritas extra-high-strength practice. Average of three full-size specimens; transverse values apply when required. Thicker plates by agreement.

Delivery Condition and Deoxidation

Deoxidation: Killed, fine-grain practice. Delivery condition: typically TMCP or QT for extra-high-strength plates; N/NR may apply at lower extra-high levels per rules. F-class (F460) grades are supplied normalized or TMCP (often with Ni alloying for -60°C toughness); as-rolled delivery is not permitted. Optional extras: UT, Z15/Z25/Z35, BV survey.

Thickness Coverage

Extra-high-strength BV A/D/E/F 420-690 plates are commonly supplied from about 6 mm to 100 mm thick (thicker by agreement under UR W16). Width 1500-4000 mm and length 6000-18000 mm are typical.

Equivalent Steel Grades of BV F460

 

Society / StandardEquivalent grade
BV (Bureau Veritas)BV F460 steel plate (LR FH46 / ABS FQ47)
LR (Lloyd's Register)LR FH46 steel plate
ABSABS FQ47 steel plate
CCSCCS F460 steel plate
DNVDNV F460 steel plate
NKNK F47 steel plate
KRKR F47 steel plate
RINARINA F460 steel plate

IACS societies align extra-high-strength hull grades under UR W16; naming differs (BV F460, LR FH46, ABS FQ47). Dual certification is common when ordered that way.

FAQ about BV F460 Steel Plate

What is BV F460 steel plate?

It is an extra-high-strength hull structural steel under Bureau Veritas Rules (IACS UR W16 extra-high-strength family), with 460 MPa minimum yield, 570-720 MPa tensile strength and Charpy toughness at -60°C [-76°F].

What does BV F460 stand for?

BV is Bureau Veritas. The letter F is the toughness class (Charpy at -60°C [-76°F]), and 460 is the yield-strength level in MPa. Market/LR naming often uses FH46; ABS often uses FQ47. Note: BV does not use AH460 — the grade is F460, not AH460.

What is the yield strength of BV F460?

Minimum 460 MPa (67 ksi), tensile 570-720 MPa (83-104 ksi), elongation about 17% min (for the common thickness range).

What is the impact test temperature for BV F460?

Charpy V-notch at -60°C [-76°F]. Typical longitudinal average minimum is 46 J (transverse 31 J) for the tabulated thickness range on this grade page.

What is the difference between BV A460, D460, E460 and F460?

Same 460 MPa strength class. Toughness class differs: A at 0°C, D at -20°C, E at -40°C, F at -60°C. Chemistry (C, P, S, Mn) is tightened for colder classes.

How does BV F460 differ from higher-strength BV AH40?

BV AH40 is UR W11 higher-strength (390 MPa). BV F460 is UR W16 extra-high-strength (460 MPa) with different chemistry and delivery practice (often TM/QT).

Is BV F460 the same as LR FH46 or ABS FQ47?

They are IACS counterparts in the extra-high-strength family; exact chemistry/delivery options differ by society edition. Dual certification is available when surveys are arranged.

Is BV F460 weldable?

Weldable with approved procedures for extra-high-strength ship steel. Preheat, heat input and consumable matching are critical; follow the mill WPS and BV welding requirements.

What heat treatment is required for BV F460?

Extra-high-strength grades are typically delivered TMCP or quenched and tempered (QT), sometimes normalized/normalized-rolled depending on strength level and thickness. F-class (F460) grades are supplied normalized or TMCP (often with Ni alloying for -60°C toughness); as-rolled delivery is not permitted. Optional extras: UT, Z15/Z25/Z35, BV survey.

What thickness is available for BV F460?

Common supply is about 6-100 mm (thicker by agreement under UR W16 / BV rules), 1500-4000 mm wide and 6000-18000 mm long.

Other BV Steel Plate Grades

BV Grade A steel plate | BV Grade B steel plate | BV Grade D steel plate | BV Grade E steel plate | BV AH32 steel plate | BV AH36 steel plate | BV AH40 steel plate | BV DH32 steel plate | BV DH36 steel plate | BV DH40 steel plate | BV EH32 steel plate | BV EH36 steel plate | BV EH40 steel plate | BV FH32 steel plate | BV FH36 steel plate | BV FH40 steel plate | BV A420 steel plate | BV A460 steel plate | BV A500 steel plate | BV A550 steel plate | BV A620 steel plate | BV A690 steel plate | BV D420 steel plate | BV D460 steel plate | BV D500 steel plate | BV D550 steel plate | BV D620 steel plate | BV D690 steel plate | BV E420 steel plate | BV E460 steel plate | BV E500 steel plate | BV E550 steel plate | BV E620 steel plate | BV E690 steel plate | BV F420 steel plate | BV F500 steel plate | BV F550 steel plate | BV F620 steel plate | BV F690 steel plate

Equivalent Class Society Grades

BV F460 corresponds to extra-high-strength counterparts under other IACS societies (LR FH46, ABS FQ47, etc.): LR FH46 steel plate, ABS FQ47 steel plate, CCS F460 steel plate, DNV F460 steel plate, NK F47 steel plate, KR F47 steel plate, RINA F460 steel plate.

Other Products