Steel Beams
ASTM A588 Grade B Weathering Wide Flange Beams

ASTM A588 Grade B W-Shapes: Weathering Wide-Flange Beams
ASTM A588 is the 50 ksi [345 MPa] HSLA weathering steel for shapes, plates and bars. Its chromium, copper, nickel and vanadium content lets a protective oxide patina form, so the steel can be used bare in suitable atmospheres. Producing mills roll A588 W-shapes mainly in the Grade B chemistry, which this page covers. Gangsteel quotes A588 Grade B wide-flange beams by full designation, for example “W14×90, ASTM A588 Grade B”; availability is confirmed per enquiry.
| Item | Value | Note |
|---|---|---|
| Material | ASTM A588/A588M Grade B | Grades A and K are other chemistries of the same specification |
| Section series | W-shapes to ASTM A6/A6M | |
| Yield point, min | 50 ksi [345 MPa] | All shapes |
| Tensile strength, min | 70 ksi [485 MPa] | 5 ksi higher than A572 Gr 50 or A992 |
| Corrosion index | 6.0 min per ASTM G101 (Larrabee-Coburn) | Calculated from the heat analysis |
| Steelmaking | Fine grain practice | Required by the specification |
Selected W-Shapes in A588 Grade B
| W shape | Metric | d in [mm] | bf in [mm] | tf in | lb/ft [kg/m] | A in² | Zx in³ | 50·Zx kip-ft [kN·m] | A·Fu kips [kN] | Flange, flexure |
|---|---|---|---|---|---|---|---|---|---|---|
| W8×31 | W200×46.1 | 8 [203] | 7.995 [203] | 0.435 | 31 [46.1] | 9.13 | 30.4 | 127 [172] | 639 [2843] | Noncompact |
| W8×48 | W200×71.4 | 8.5 [216] | 8.11 [206] | 0.685 | 48 [71.4] | 14.1 | 49 | 204 [277] | 987 [4390] | Compact |
| W10×33 | W250×49.1 | 9.73 [247] | 7.96 [202] | 0.435 | 33 [49.1] | 9.71 | 38.8 | 162 [219] | 680 [3023] | Compact |
| W10×49 | W250×72.9 | 9.98 [253] | 10 [254] | 0.56 | 49 [72.9] | 14.4 | 60.4 | 252 [341] | 1008 [4484] | Compact |
| W10×77 | W250×115 | 10.6 [269] | 10.19 [259] | 0.87 | 77 [114.6] | 22.6 | 97.6 | 407 [551] | 1582 [7037] | Compact |
| W12×26 | W310×38.7 | 12.22 [310] | 6.49 [165] | 0.38 | 26 [38.7] | 7.65 | 37.2 | 155 [210] | 536 [2382] | Compact |
| W12×65 | W310×96.7 | 12.12 [308] | 12 [305] | 0.605 | 65 [96.7] | 19.1 | 96.8 | 403 [547] | 1337 [5947] | Noncompact |
| W12×96 | W310×143 | 12.71 [323] | 12.16 [309] | 0.9 | 96 [142.9] | 28.2 | 147 | 612 [830] | 1974 [8781] | Compact |
| W14×22 | W360×32.7 | 13.74 [349] | 5 [127] | 0.335 | 22 [32.7] | 6.49 | 33.2 | 138 [188] | 454 [2021] | Compact |
| W14×48 | W360×71.4 | 13.79 [350] | 8.03 [204] | 0.595 | 48 [71.4] | 14.1 | 78.4 | 327 [443] | 987 [4390] | Compact |
| W14×90 | W360×134 | 14.02 [356] | 14.52 [369] | 0.71 | 90 [133.9] | 26.5 | 157 | 654 [887] | 1855 [8251] | Noncompact |
| W14×99 | W360×147 | 14.16 [360] | 14.565 [370] | 0.78 | 99 [147.3] | 29.1 | 173 | 721 [977] | 2037 [9061] | Noncompact |
| W14×233 | W360×347 | 16.04 [407] | 15.89 [404] | 1.72 | 233 [346.7] | 68.5 | 436 | 1817 [2463] | 4795 [21329] | Compact |
| W14×426 | W360×634 | 18.67 [474] | 16.695 [424] | 3.035 | 426 [634.0] | 125 | 869 | 3621 [4909] | 8750 [38922] | Compact |
| W14×730 | W360×1086 | 22.42 [569] | 17.89 [454] | 4.91 | 730 [1086.4] | 215 | 1660 | 6917 [9378] | 15050 [66946] | Compact |
| W16×40 | W410×59.5 | 16.01 [407] | 6.995 [178] | 0.505 | 40 [59.5] | 11.8 | 73 | 304 [412] | 826 [3674] | Compact |
| W16×67 | W410×99.7 | 16.33 [415] | 10.235 [260] | 0.665 | 67 [99.7] | 19.7 | 130 | 542 [734] | 1379 [6134] | Compact |
| W18×50 | W460×74.4 | 17.99 [457] | 7.495 [190] | 0.57 | 50 [74.4] | 14.7 | 101 | 421 [571] | 1029 [4577] | Compact |
| W18×97 | W460×144 | 18.59 [472] | 11.145 [283] | 0.87 | 97 [144.4] | 28.5 | 211 | 879 [1192] | 1995 [8874] | Compact |
| W21×48 | W530×71.4 | 20.62 [524] | 8.14 [207] | 0.43 | 48 [71.4] | 14.1 | 107 | 446 [604] | 987 [4390] | Noncompact |
| W21×68 | W530×101 | 21.13 [537] | 8.27 [210] | 0.685 | 68 [101.2] | 20 | 160 | 667 [904] | 1400 [6228] | Compact |
| W21×101 | W530×150 | 21.36 [543] | 12.29 [312] | 0.8 | 101 [150.3] | 29.8 | 253 | 1054 [1429] | 2086 [9279] | Compact |
| W24×55 | W610×81.8 | 23.57 [599] | 7.005 [178] | 0.505 | 55 [81.8] | 16.2 | 134 | 558 [757] | 1134 [5044] | Compact |
| W24×84 | W610×125 | 24.1 [612] | 9.02 [229] | 0.77 | 84 [125.0] | 24.7 | 224 | 933 [1265] | 1729 [7691] | Compact |
| W24×146 | W610×217 | 24.74 [628] | 12.9 [328] | 1.09 | 146 [217.3] | 43 | 418 | 1742 [2361] | 3010 [13389] | Compact |
| W27×94 | W690×140 | 26.92 [684] | 9.99 [254] | 0.745 | 94 [139.9] | 27.7 | 278 | 1158 [1570] | 1939 [8625] | Compact |
| W30×99 | W760×147 | 29.65 [753] | 10.45 [265] | 0.67 | 99 [147.3] | 29.1 | 312 | 1300 [1763] | 2037 [9061] | Compact |
| W33×130 | W840×193 | 33.09 [840] | 11.51 [292] | 0.855 | 130 [193.5] | 38.3 | 467 | 1946 [2638] | 2681 [11926] | Compact |
| W36×150 | W920×223 | 35.85 [911] | 11.975 [304] | 0.94 | 150 [223.2] | 44.2 | 581 | 2421 [3282] | 3094 [13763] | Compact |
| W36×302 | W920×449 | 37.33 [948] | 16.655 [423] | 1.68 | 302 [449.4] | 88.8 | 1280 | 5333 [7231] | 6216 [27650] | Compact |
| W40×199 | W1000×296 | 38.67 [982] | 15.75 [400] | 1.065 | 199 [296.1] | 58.4 | 869 | 3621 [4909] | 4088 [18184] | Compact |
| W44×230 | W1100×342 | 42.91 [1090] | 15.75 [400] | 1.22 | 230 [342.3] | 67.9 | 1100 | 4583 [6214] | 4753 [21142] | Compact |
The plastic-moment column is Fy·Zx with Fy = 50 ksi: a characteristic cross-section value. It is not a design strength or safe load: it excludes the resistance factor or safety factor, lateral-torsional buckling, flange local buckling for noncompact flanges, shear and serviceability. Compactness uses the AISC 360 limits for flanges of rolled I-shapes in flexure: compact when bf/2tf ≤ 0.38√(E/Fy), noncompact up to 1.0√(E/Fy), with E = 29,000 ksi. Webs of standard W-shapes are compact in flexure at these yield levels; web slenderness in compression is a separate check for the design engineer.
A·Fu is the gross area multiplied by the 70 ksi minimum tensile strength, shown to compare tensile rupture potential with 65 ksi grades. Net-section rupture uses the effective net area at connections, not the gross area. Flange compactness is the same as for other 50 ksi grades: W21×48, W14×99, W14×90, W12×65, W8×31 are noncompact in flexure.
A588 Grade B Chemistry
| Element | Grade B | Grade A (for comparison) |
|---|---|---|
| Carbon, max | 0.20 | 0.19 |
| Manganese | 0.75–1.35 | 0.80–1.25 |
| Phosphorus, max | 0.030 (0.04 permitted for shapes) | 0.030 (0.04 for shapes) |
| Sulfur, max | 0.030 (0.05 permitted for shapes) | 0.030 (0.05 for shapes) |
| Silicon | 0.15–0.50 | 0.30–0.65 |
| Nickel, max | 0.50 | 0.40 |
| Chromium | 0.40–0.70 | 0.40–0.65 |
| Copper | 0.20–0.40 | 0.25–0.40 |
| Vanadium | 0.01–0.10 | 0.02–0.10 |
For each 0.01 point of carbon below the maximum, manganese may rise 0.06 point above its maximum, up to 1.50%. The corrosion index of at least 6.0 is calculated from the heat analysis, and the mill can be asked for evidence of corrosion resistance. Grade A and Grade B are not interchangeable on a certificate unless the order allows either.
A588 Tensile Requirements for Shapes
| Property | Inch-pound | SI |
|---|---|---|
| Yield point, min | 50 ksi | 345 MPa |
| Tensile strength, min | 70 ksi | 485 MPa |
| Elongation in 8 in [200 mm], min | 18% | 18% |
| Elongation in 2 in [50 mm], min | 21% (18% for W-shapes with flanges over 3 in) | 21% (18%) |
Designing and Detailing Bare Weathering W-Shapes
- Use bare A588 only where surfaces wet and dry in cycles; continuous wetness, de-icing salts, coastal chloride exposure and industrial atmospheres with high sulfur dioxide can prevent a stable patina.
- Detail for drainage: avoid pockets between flanges and stiffeners, seal or open crevices, and slope or cope members so water leaves the section.
- Allow for run-off staining of concrete and masonry during patina formation.
- Use weathering-grade bolts (ASTM F3125 Type 3) and welding consumables that match the corrosion resistance for exposed welds.
- Paint or galvanize if the environment is unsuitable; A588 then still gives 50 ksi strength, but the weathering benefit is not used.
AISC directs W-shapes with weathering characteristics to A588 for building construction and to A709 Grade 50W for bridges. A709 50W is a bridge specification with its own toughness zones and is not covered here. For European weathering grades the equivalent family is EN 10025-5 (S355J2W and related grades), which uses European section series. For a cold-impact EN grade in standard steel see EN 10025-2 S355J2 HEA and HEB beams.
A588 Compared with A572 Grade 50 and A992
| Specification | Fy / Fu min | Weathering | Note |
|---|---|---|---|
| ASTM A588 Grade B | 50 / 70 ksi | Yes, index ≥ 6.0 | Cr-Cu-Ni-V chemistry |
| ASTM A572 Grade 50 | 50 / 65 ksi | No | Nb, V or Ti/N microalloyed |
| ASTM A992 | 50–65 / 65 ksi | No | Preferred for W-shapes in buildings; see ASTM A992 wide-flange beams |
A572 and A588 are separate specifications; A588 is not to be substituted for A572 without the purchaser’s agreement. Plates for connections in the same weathering chemistry are covered by ASTM A588 Grade B steel plate.
Delivery, Inspection and Lead Time
| Item | Specify | Reason |
|---|---|---|
| Shape | Full W designation | Nominal depth alone does not fix weight, flange width or thickness |
| Material | ASTM A588/A588M Grade B | The grade name must match the certificate |
| Dimensions and tolerances | ASTM A6/A6M permissible variations | Nominal catalogue values are not tolerances |
| Toughness | Charpy only if specified (A6/A6M S5 or S30) | Not required by the base specification |
| Certificate | EN 10204 3.1 or mill test report with corrosion index | Traceability to the supplied heat |
| Mass basis | Theoretical or weighed | Avoids invoicing disputes |
Weathering W-shapes are rolled less frequently than A992 multi-grade shapes, so plan the order early.
Lead time: typical delivery is about 35 days for mill orders, and sizes available from stock can ship in 1–3 days. Availability is confirmed shape by shape at enquiry; the W-shape table on this page is reference geometry, not a stock list.
RFQ Checklist
- Exact W designation (e.g. W14×90 or metric W360×134), quantity and lengths in feet or metres.
- ASTM A588/A588M Grade B with edition if the project fixes one, plus any supplementary requirements (for example Charpy testing under ASTM A6/A6M S5 or S30).
- Whether a multi-certified certificate (for example A992 / A572 Gr 50 / A36) is acceptable or a single specification is required.
- Processing: cutting, coping, drilling, blasting, priming; inspection document and third-party inspection if needed.
- Packing, marking and destination; whether stock shapes for 1–3 day dispatch are preferred over a mill order.
The same W-shapes in other ASTM materials: A992, A36, A572 Grade 50.
Frequently Asked Questions
What is an A588 wide-flange beam?
A W-shape rolled to ASTM A6/A6M dimensions from ASTM A588 weathering steel: 50 ksi minimum yield, 70 ksi minimum tensile, with Cr, Cu, Ni and V that let it form a protective patina.
Why Grade B and not Grade A?
Producing mills generally roll A588 W-shapes in the Grade B chemistry. Grade A has a slightly different composition; both meet the same tensile requirements, but the certificate must match the ordered grade.
Can A588 W-shapes be left unpainted?
Yes, in atmospheres where the surface wets and dries in cycles and chloride exposure is low, with detailing that drains water. In marine splash zones, under de-icing salt spray or where the steel stays wet, coat the members.
Is A588 the same as Corten?
Corten is a trade name for weathering steels; A588 is the ASTM specification. They are similar in purpose, but order and certify to A588/A588M.
Why is A588’s tensile strength higher than A992’s?
A588 specifies 70 ksi minimum tensile strength for shapes, against 65 ksi for A992 and A572 Grade 50. Yield is 50 ksi minimum in all three.
Which bolts should be used with bare A588 beams?
Weathering-grade high-strength bolts such as ASTM F3125 Type 3, with matching nuts and washers, so the fasteners corrode at a similar rate to the steel.
Can A588 replace A572 Grade 50 on an order?
Only with the purchaser’s agreement. A572 states that A588 is not to be substituted without agreement, even though the strength is comparable.
What lead time applies to A588 Grade B W-shapes?
About 35 days for mill orders and 1–3 days for stock shapes. Weathering shapes are rolled on fewer cycles, so confirm the rolling date at enquiry.
