
ASTM A572 Grade 50 W-Shapes: HSLA Wide-Flange Beams
ASTM A572 Grade 50 is a high-strength low-alloy columbium-vanadium steel with a 50 ksi [345 MPa] minimum yield point and 65 ksi [450 MPa] minimum tensile strength. In W-shapes it covers the same ASTM A6/A6M sizes as A992 without A992’s maximum-yield and yield-to-tensile limits. Gangsteel quotes A572 Grade 50 wide-flange beams by full designation, for example “W21×68, ASTM A572 Grade 50”, keeping A572 as the specified material rather than converting it to A992.
| Item | Value | Note |
|---|---|---|
| Material | ASTM A572/A572M Grade 50 [345] | HSLA; microalloy type 1, 2, 3 or 5 at producer’s option |
| Section series | W-shapes to ASTM A6/A6M | All flange thicknesses permitted for Grade 50 |
| Yield point, min | 50 ksi [345 MPa] | No specified maximum |
| Tensile strength, min | 65 ksi [450 MPa] | No yield-to-tensile limit in A572 |
| Toughness | Only when specified | Notch toughness is to be negotiated for welded bridges |
Selected W-Shapes in A572 Grade 50
| W shape | Metric | d in [mm] | bf in [mm] | tw in | tf in | lb/ft [kg/m] | Zx in³ | 50·Zx kip-ft [kN·m] | bf/2tf | Flange, flexure at 50 ksi |
|---|---|---|---|---|---|---|---|---|---|---|
| W8×31 | W200×46.1 | 8 [203] | 7.995 [203] | 0.285 | 0.435 | 31 [46.1] | 30.4 | 127 [172] | 9.19 | Noncompact (compact at 36 ksi) |
| W8×48 | W200×71.4 | 8.5 [216] | 8.11 [206] | 0.4 | 0.685 | 48 [71.4] | 49 | 204 [277] | 5.92 | Compact |
| W10×33 | W250×49.1 | 9.73 [247] | 7.96 [202] | 0.29 | 0.435 | 33 [49.1] | 38.8 | 162 [219] | 9.15 | Compact |
| W10×49 | W250×72.9 | 9.98 [253] | 10 [254] | 0.34 | 0.56 | 49 [72.9] | 60.4 | 252 [341] | 8.93 | Compact |
| W10×77 | W250×115 | 10.6 [269] | 10.19 [259] | 0.53 | 0.87 | 77 [114.6] | 97.6 | 407 [551] | 5.86 | Compact |
| W12×26 | W310×38.7 | 12.22 [310] | 6.49 [165] | 0.23 | 0.38 | 26 [38.7] | 37.2 | 155 [210] | 8.54 | Compact |
| W12×65 | W310×96.7 | 12.12 [308] | 12 [305] | 0.39 | 0.605 | 65 [96.7] | 96.8 | 403 [547] | 9.92 | Noncompact (compact at 36 ksi) |
| W12×96 | W310×143 | 12.71 [323] | 12.16 [309] | 0.55 | 0.9 | 96 [142.9] | 147 | 612 [830] | 6.76 | Compact |
| W14×22 | W360×32.7 | 13.74 [349] | 5 [127] | 0.23 | 0.335 | 22 [32.7] | 33.2 | 138 [188] | 7.46 | Compact |
| W14×48 | W360×71.4 | 13.79 [350] | 8.03 [204] | 0.34 | 0.595 | 48 [71.4] | 78.4 | 327 [443] | 6.75 | Compact |
| W14×90 | W360×134 | 14.02 [356] | 14.52 [369] | 0.44 | 0.71 | 90 [133.9] | 157 | 654 [887] | 10.23 | Noncompact (compact at 36 ksi) |
| W14×99 | W360×147 | 14.16 [360] | 14.565 [370] | 0.485 | 0.78 | 99 [147.3] | 173 | 721 [977] | 9.34 | Noncompact (compact at 36 ksi) |
| W14×233 | W360×347 | 16.04 [407] | 15.89 [404] | 1.07 | 1.72 | 233 [346.7] | 436 | 1817 [2463] | 4.62 | Compact |
| W14×426 | W360×634 | 18.67 [474] | 16.695 [424] | 1.875 | 3.035 | 426 [634.0] | 869 | 3621 [4909] | 2.75 | Compact |
| W14×730 | W360×1086 | 22.42 [569] | 17.89 [454] | 3.07 | 4.91 | 730 [1086.4] | 1660 | 6917 [9378] | 1.82 | Compact |
| W16×40 | W410×59.5 | 16.01 [407] | 6.995 [178] | 0.305 | 0.505 | 40 [59.5] | 73 | 304 [412] | 6.93 | Compact |
| W16×67 | W410×99.7 | 16.33 [415] | 10.235 [260] | 0.395 | 0.665 | 67 [99.7] | 130 | 542 [734] | 7.70 | Compact |
| W18×50 | W460×74.4 | 17.99 [457] | 7.495 [190] | 0.355 | 0.57 | 50 [74.4] | 101 | 421 [571] | 6.57 | Compact |
| W18×97 | W460×144 | 18.59 [472] | 11.145 [283] | 0.535 | 0.87 | 97 [144.4] | 211 | 879 [1192] | 6.41 | Compact |
| W21×48 | W530×71.4 | 20.62 [524] | 8.14 [207] | 0.35 | 0.43 | 48 [71.4] | 107 | 446 [604] | 9.47 | Noncompact (compact at 36 ksi) |
| W21×68 | W530×101 | 21.13 [537] | 8.27 [210] | 0.43 | 0.685 | 68 [101.2] | 160 | 667 [904] | 6.04 | Compact |
| W21×101 | W530×150 | 21.36 [543] | 12.29 [312] | 0.5 | 0.8 | 101 [150.3] | 253 | 1054 [1429] | 7.68 | Compact |
| W24×55 | W610×81.8 | 23.57 [599] | 7.005 [178] | 0.395 | 0.505 | 55 [81.8] | 134 | 558 [757] | 6.94 | Compact |
| W24×84 | W610×125 | 24.1 [612] | 9.02 [229] | 0.47 | 0.77 | 84 [125.0] | 224 | 933 [1265] | 5.86 | Compact |
| W24×146 | W610×217 | 24.74 [628] | 12.9 [328] | 0.65 | 1.09 | 146 [217.3] | 418 | 1742 [2361] | 5.92 | Compact |
| W27×94 | W690×140 | 26.92 [684] | 9.99 [254] | 0.49 | 0.745 | 94 [139.9] | 278 | 1158 [1570] | 6.70 | Compact |
| W30×99 | W760×147 | 29.65 [753] | 10.45 [265] | 0.52 | 0.67 | 99 [147.3] | 312 | 1300 [1763] | 7.80 | Compact |
| W33×130 | W840×193 | 33.09 [840] | 11.51 [292] | 0.58 | 0.855 | 130 [193.5] | 467 | 1946 [2638] | 6.73 | Compact |
| W36×150 | W920×223 | 35.85 [911] | 11.975 [304] | 0.625 | 0.94 | 150 [223.2] | 581 | 2421 [3282] | 6.37 | Compact |
| W36×302 | W920×449 | 37.33 [948] | 16.655 [423] | 0.945 | 1.68 | 302 [449.4] | 1280 | 5333 [7231] | 4.96 | Compact |
| W40×199 | W1000×296 | 38.67 [982] | 15.75 [400] | 0.65 | 1.065 | 199 [296.1] | 869 | 3621 [4909] | 7.39 | Compact |
| W44×230 | W1100×342 | 42.91 [1090] | 15.75 [400] | 0.71 | 1.22 | 230 [342.3] | 1100 | 4583 [6214] | 6.45 | Compact |
The plastic-moment column is Fy·Zx with Fy = 50 ksi: a characteristic cross-section value. It is not a design strength or safe load: it excludes the resistance factor or safety factor, lateral-torsional buckling, flange local buckling for noncompact flanges, shear and serviceability. Compactness uses the AISC 360 limits for flanges of rolled I-shapes in flexure: compact when bf/2tf ≤ 0.38√(E/Fy), noncompact up to 1.0√(E/Fy), with E = 29,000 ksi. Webs of standard W-shapes are compact in flexure at these yield levels; web slenderness in compression is a separate check for the design engineer.
Raising Fy from 36 to 50 ksi lowers the compact-flange limit from about 10.8 to 9.15. In the producing-mill range used here five W-shapes cross it and become noncompact in flexure: W21×48, W14×99, W14×90, W12×65, W8×31. Their flexural strength is reduced for flange local buckling, which design tables already reflect; if a design was checked in A36 and the material is upgraded to Grade 50, these shapes need the recheck. None of the W-shapes in this range has a slender flange for compression at 50 ksi (limit about 13.5).
A572 Grade 50 Chemistry for Shapes
| Element | Requirement | Note |
|---|---|---|
| Carbon, max | 0.23 | |
| Manganese | 0.50 min, 1.35 max | Mn:C at least 2:1; each 0.01 below max C allows +0.06 Mn, up to 1.60 |
| Phosphorus, max | 0.030 | |
| Sulfur, max | 0.030 | |
| Silicon | 0.40 max (flanges to 3 in); 0.15–0.40 (flanges over 3 in) | |
| Copper, min | 0.20 when copper steel is specified | |
| Microalloying | Type 1: Nb 0.005–0.05; Type 2: V 0.01–0.15; Type 3: Nb + V; Type 5: Ti, N and V combinations | Producer’s option unless the order names a type |
A572 itself sets no carbon-equivalent limit. Where welding procedures depend on one, add the A572 supplementary requirement for a maximum CE or state a CE limit in the order, or specify A992, which has a CE maximum built in. Copper, nickel, chromium and molybdenum are not specified for Grade 50; ask for them to be reported if the welding procedure or CE calculation needs them.
A572 Grade 50 Tensile Requirements
| Property | Inch-pound | SI |
|---|---|---|
| Yield point, min | 50 ksi | 345 MPa |
| Tensile strength, min | 65 ksi | 450 MPa |
| Elongation in 8 in [200 mm], min | 18% | 18% |
| Elongation in 2 in [50 mm], min | 21% (19% for the heaviest wide-flange shapes) | 21% (19%) |
A572 Grade 50 vs A992 for W-Shapes
| Requirement | ASTM A572 Grade 50 | ASTM A992 |
|---|---|---|
| Yield | 50 ksi min, no max | 50–65 ksi |
| Yield / tensile ratio | not limited | 0.85 max |
| Carbon equivalent | not limited unless supplementary requirement | 0.45 max (0.47 for flanges over 2 in) |
| Microalloy | Nb, V, Ti/N types required | limits on V, Nb and residuals |
| Product forms | plates, shapes, bars, sheet piling | structural shapes only |
A992 was developed from A572 Grade 50 with added controls for building frames, especially for seismic design where an upper bound on yield matters. A buyer who specifies A572 Grade 50 should accept A992 only if the project allows; mills that multi-certify issue one report showing both. The requirements of A992 are covered on ASTM A992 wide-flange beams.
Grade 50 is often compared with EN S355JR: 345 MPa against 355 MPa nominal yield, but S355JR has a +20 °C Charpy requirement and CEV limits, and HE sections are a different series. See EN 10025-2 S355JR HEA and HEB beams and S355JR IPE beams for European sections.
Fabrication Notes for A572 Grade 50 W-Shapes
Welding follows the structural welding code for a 50 ksi base metal with matching E70 consumables. Check preheat for heavy W14 and W36 flanges, and order a CE limit if the procedure relies on one. Thermal cutting of flange copes and beam penetrations is routine; grind re-entrant corners. For gussets, cap plates and splice plates in the same grade use ASTM A572 Grade 50 steel plate.
Delivery, Inspection and Lead Time
| Item | Specify | Reason |
|---|---|---|
| Shape | Full W designation | Nominal depth alone does not fix weight, flange width or thickness |
| Material | ASTM A572/A572M Grade 50; microalloy type if required | The grade name must match the certificate |
| Dimensions and tolerances | ASTM A6/A6M permissible variations | Nominal catalogue values are not tolerances |
| Toughness | Charpy only if specified (A6/A6M S5 or S30) | Not required by the base specification |
| Certificate | EN 10204 3.1 or mill test report showing type and chemistry | Traceability to the supplied heat |
| Mass basis | Theoretical or weighed | Avoids invoicing disputes |
Lead time: typical delivery is about 35 days for mill orders, and sizes available from stock can ship in 1–3 days. Availability is confirmed shape by shape at enquiry; the W-shape table on this page is reference geometry, not a stock list.
RFQ Checklist
- Exact W designation (e.g. W14×90 or metric W360×134), quantity and lengths in feet or metres.
- ASTM A572/A572M Grade 50 with edition if the project fixes one, plus any supplementary requirements (for example Charpy testing under ASTM A6/A6M S5 or S30).
- Whether a multi-certified certificate (for example A992 / A572 Gr 50 / A36) is acceptable or a single specification is required.
- Processing: cutting, coping, drilling, blasting, priming; inspection document and third-party inspection if needed.
- Packing, marking and destination; whether stock shapes for 1–3 day dispatch are preferred over a mill order.
The same W-shapes in other ASTM materials: A992, A36, A588 Grade B.
Frequently Asked Questions
What is ASTM A572 Grade 50 in a wide-flange beam?
A W-shape rolled to ASTM A6/A6M dimensions from HSLA steel with 50 ksi [345 MPa] minimum yield and 65 ksi [450 MPa] minimum tensile strength, using Nb, V or Ti/N microalloying.
Is A572 Grade 50 the same as A992?
No. Both have 50 ksi minimum yield and 65 ksi minimum tensile, but A992 also limits yield to 65 ksi, the yield-to-tensile ratio to 0.85 and the carbon equivalent. Many mills certify W-shapes to both.
Which W-shapes are noncompact in A572 Grade 50?
In this range: W21×48, W14×99, W14×90, W12×65 and W8×31. Their bf/2tf exceeds the 50 ksi compact limit of about 9.15.
Can A572 Grade 65 be supplied in W-shapes?
Grade 65 is limited to shapes with thinner flanges and is rolled only on certain sections, so it is quoted case by case and is not covered on this page.
What does the microalloy “Type” mean on an A572 certificate?
It identifies the strengthening elements used: Type 1 niobium, Type 2 vanadium, Type 3 niobium plus vanadium, Type 5 titanium/nitrogen/vanadium combinations. The producer chooses unless the order specifies one.
Does A572 Grade 50 have a carbon-equivalent limit?
Not in the base specification. Add a CE limit by supplementary requirement or in the order, or specify A992.
Is A572 Grade 50 equivalent to S355JR?
They are similar in strength but not interchangeable on a certificate: S355JR has a +20 °C Charpy test and CEV limits and is supplied in European section series.
What is the lead time for A572 Grade 50 W-shapes?
About 35 days for mill orders and 1–3 days for shapes in stock, confirmed per designation.
