Steel Beams
ASTM A36 Wide Flange Beams: W-Shape Sizes & Data

ASTM A36 W-Shapes: Carbon Steel Wide-Flange Beams and Columns
ASTM A36 is the carbon structural steel specification with a 36 ksi [250 MPa] minimum yield point. Applied to ASTM A6/A6M wide-flange shapes, it gives the lower-strength option for W beams and columns: framing for industrial buildings, platforms, pipe racks, equipment supports and secondary members where stiffness, connection geometry or a project specification sets the choice. Gangsteel quotes A36 W-shapes by full designation, for example “W12×26, ASTM A36”; sizes, quantity and availability are confirmed per enquiry.
| Item | Value | Note |
|---|---|---|
| Material | ASTM A36/A36M | Carbon structural steel; one strength level |
| Section series | W-shapes, dimensions and tolerances to ASTM A6/A6M | Same geometry as A992 or A572 W-shapes of the same designation |
| Yield point, min | 36 ksi [250 MPa] | No maximum yield in the specification |
| Tensile strength | 58–80 ksi [400–550 MPa] | No 80 ksi maximum for W-shapes with flanges over 3 in [75 mm] |
| Toughness | Not required unless specified | Supplementary Charpy requirements S5 / S30 of A6/A6M by agreement |
Selected W-Shapes in A36
| W shape | Metric | d in [mm] | bf in [mm] | tf in | lb/ft [kg/m] | Zx in³ | 36·Zx kip-ft [kN·m] | bf/2tf | Flange, flexure | tf > 3 in |
|---|---|---|---|---|---|---|---|---|---|---|
| W8×31 | W200×46.1 | 8 [203] | 7.995 [203] | 0.435 | 31 [46.1] | 30.4 | 91 [124] | 9.19 | Compact | – |
| W8×48 | W200×71.4 | 8.5 [216] | 8.11 [206] | 0.685 | 48 [71.4] | 49 | 147 [199] | 5.92 | Compact | – |
| W10×33 | W250×49.1 | 9.73 [247] | 7.96 [202] | 0.435 | 33 [49.1] | 38.8 | 116 [158] | 9.15 | Compact | – |
| W10×49 | W250×72.9 | 9.98 [253] | 10 [254] | 0.56 | 49 [72.9] | 60.4 | 181 [246] | 8.93 | Compact | – |
| W10×77 | W250×115 | 10.6 [269] | 10.19 [259] | 0.87 | 77 [114.6] | 97.6 | 293 [397] | 5.86 | Compact | – |
| W12×26 | W310×38.7 | 12.22 [310] | 6.49 [165] | 0.38 | 26 [38.7] | 37.2 | 112 [151] | 8.54 | Compact | – |
| W12×65 | W310×96.7 | 12.12 [308] | 12 [305] | 0.605 | 65 [96.7] | 96.8 | 290 [394] | 9.92 | Compact | – |
| W12×96 | W310×143 | 12.71 [323] | 12.16 [309] | 0.9 | 96 [142.9] | 147 | 441 [598] | 6.76 | Compact | – |
| W14×22 | W360×32.7 | 13.74 [349] | 5 [127] | 0.335 | 22 [32.7] | 33.2 | 100 [135] | 7.46 | Compact | – |
| W14×48 | W360×71.4 | 13.79 [350] | 8.03 [204] | 0.595 | 48 [71.4] | 78.4 | 235 [319] | 6.75 | Compact | – |
| W14×90 | W360×134 | 14.02 [356] | 14.52 [369] | 0.71 | 90 [133.9] | 157 | 471 [639] | 10.23 | Compact | – |
| W14×99 | W360×147 | 14.16 [360] | 14.565 [370] | 0.78 | 99 [147.3] | 173 | 519 [704] | 9.34 | Compact | – |
| W14×233 | W360×347 | 16.04 [407] | 15.89 [404] | 1.72 | 233 [346.7] | 436 | 1308 [1773] | 4.62 | Compact | – |
| W14×426 | W360×634 | 18.67 [474] | 16.695 [424] | 3.035 | 426 [634.0] | 869 | 2607 [3535] | 2.75 | Compact | Heavy-shape rules |
| W14×730 | W360×1086 | 22.42 [569] | 17.89 [454] | 4.91 | 730 [1086.4] | 1660 | 4980 [6752] | 1.82 | Compact | Heavy-shape rules |
| W16×40 | W410×59.5 | 16.01 [407] | 6.995 [178] | 0.505 | 40 [59.5] | 73 | 219 [297] | 6.93 | Compact | – |
| W16×67 | W410×99.7 | 16.33 [415] | 10.235 [260] | 0.665 | 67 [99.7] | 130 | 390 [529] | 7.70 | Compact | – |
| W18×50 | W460×74.4 | 17.99 [457] | 7.495 [190] | 0.57 | 50 [74.4] | 101 | 303 [411] | 6.57 | Compact | – |
| W18×97 | W460×144 | 18.59 [472] | 11.145 [283] | 0.87 | 97 [144.4] | 211 | 633 [858] | 6.41 | Compact | – |
| W21×48 | W530×71.4 | 20.62 [524] | 8.14 [207] | 0.43 | 48 [71.4] | 107 | 321 [435] | 9.47 | Compact | – |
| W21×68 | W530×101 | 21.13 [537] | 8.27 [210] | 0.685 | 68 [101.2] | 160 | 480 [651] | 6.04 | Compact | – |
| W21×101 | W530×150 | 21.36 [543] | 12.29 [312] | 0.8 | 101 [150.3] | 253 | 759 [1029] | 7.68 | Compact | – |
| W24×55 | W610×81.8 | 23.57 [599] | 7.005 [178] | 0.505 | 55 [81.8] | 134 | 402 [545] | 6.94 | Compact | – |
| W24×84 | W610×125 | 24.1 [612] | 9.02 [229] | 0.77 | 84 [125.0] | 224 | 672 [911] | 5.86 | Compact | – |
| W24×146 | W610×217 | 24.74 [628] | 12.9 [328] | 1.09 | 146 [217.3] | 418 | 1254 [1700] | 5.92 | Compact | – |
| W27×94 | W690×140 | 26.92 [684] | 9.99 [254] | 0.745 | 94 [139.9] | 278 | 834 [1131] | 6.70 | Compact | – |
| W30×99 | W760×147 | 29.65 [753] | 10.45 [265] | 0.67 | 99 [147.3] | 312 | 936 [1269] | 7.80 | Compact | – |
| W33×130 | W840×193 | 33.09 [840] | 11.51 [292] | 0.855 | 130 [193.5] | 467 | 1401 [1900] | 6.73 | Compact | – |
| W36×150 | W920×223 | 35.85 [911] | 11.975 [304] | 0.94 | 150 [223.2] | 581 | 1743 [2363] | 6.37 | Compact | – |
| W36×302 | W920×449 | 37.33 [948] | 16.655 [423] | 1.68 | 302 [449.4] | 1280 | 3840 [5206] | 4.96 | Compact | – |
| W40×199 | W1000×296 | 38.67 [982] | 15.75 [400] | 1.065 | 199 [296.1] | 869 | 2607 [3535] | 7.39 | Compact | – |
| W44×230 | W1100×342 | 42.91 [1090] | 15.75 [400] | 1.22 | 230 [342.3] | 1100 | 3300 [4474] | 6.45 | Compact | – |
The plastic-moment column is Fy·Zx with Fy = 36 ksi: a characteristic cross-section value. It is not a design strength or safe load: it excludes the resistance factor or safety factor, lateral-torsional buckling, flange local buckling for noncompact flanges, shear and serviceability. Compactness uses the AISC 360 limits for flanges of rolled I-shapes in flexure: compact when bf/2tf ≤ 0.38√(E/Fy), noncompact up to 1.0√(E/Fy), with E = 29,000 ksi. Webs of standard W-shapes are compact in flexure at these yield levels; web slenderness in compression is a separate check for the design engineer.
At 36 ksi every W-shape in the producing-mill range used here has compact flanges in flexure, because the compact limit rises to about 10.8. That includes the five shapes that become noncompact at 50 ksi: W21×48, W14×99, W14×90, W12×65, W8×31. A designer moving from A36 to a 50 ksi grade has to recheck those five for flange local buckling; the reverse change never introduces a noncompact flange.
A36 Chemistry for Shapes
| Element | All shapes | Shapes with flange thickness over 3 in [75 mm] |
|---|---|---|
| Carbon, max | 0.26 | 0.26 |
| Manganese | no requirement | 0.85–1.35 |
| Phosphorus, max | 0.04 | 0.04 |
| Sulfur, max | 0.05 | 0.05 |
| Silicon | 0.40 max | 0.15–0.40 |
| Copper, min (when copper steel is specified) | 0.20 | 0.20 |
Only the heaviest W-shapes have flanges over 3 in; in the mill range used here they are W40×593, W14×730, W14×665, W14×605, W14×550, W14×500, W14×455, W14×426. For these jumbo column sections A36 adds a manganese range and a silicon minimum, and the tensile and elongation rules change. A36 sets no carbon-equivalent limit, so weldability on a certificate is judged from the reported C, Mn and residuals; agree a CE limit in the order if the welding procedure depends on one.
A36 Tensile Requirements for W-Shapes
| Property | Inch-pound | SI |
|---|---|---|
| Yield point, min | 36 ksi | 250 MPa |
| Tensile strength | 58–80 ksi | 400–550 MPa |
| Elongation in 8 in [200 mm], min | 20% | 20% |
| Elongation in 2 in [50 mm], min | 21% | 21% |
| W-shapes with flanges over 3 in | 58 ksi min, no maximum; 19% in 2 in | 400 MPa min, no maximum; 19% in 50 mm |
The 8 in and 2 in gauge lengths are alternative specimen bases. A36 has no upper limit on yield, so a heat can exceed 50 ksi and still be A36. For seismic or capacity-designed connections the expected yield must be taken from the design code, not from the 36 ksi minimum.
A36, A992 and A572 Grade 50 for the Same W-Shape
| Specification | Fy min | Fu | Typical use for W-shapes |
|---|---|---|---|
| ASTM A36 | 36 ksi [250 MPa] | 58–80 ksi | Specified where a project or older design calls for it |
| ASTM A572 Gr 50 | 50 ksi [345 MPa] | 65 ksi min | HSLA option; no maximum yield |
| ASTM A992 | 50–65 ksi [345–450 MPa] | 65 ksi min; Fy/Fu ≤ 0.85 | The preferred specification for W-shapes in U.S. practice |
Some North American producers certify W-shapes to A992, A572 Grade 50 and A36 on one test report, so steel ordered as A36 may arrive with multi-grade certification and a yield far above 36 ksi. That is acceptable for strength checks but matters where an upper bound on strength is part of the design. See ASTM A992 wide-flange beams for the A992 requirements.
A36 is not the same as EN S235JR: the yield values are close (36 ksi = 248 MPa), but S235JR carries a 27 J Charpy test at +20 °C, a CEV limit and different section series. For European sections in that grade see EN 10025-2 S235JR HEA and HEB beams and S235JR IPE beams.
Fabrication Notes for A36 W-Shapes
A36 W-shapes weld readily with common processes; preheat follows the welding code for the thickest part joined, which for jumbo W14 columns can be substantial. Coping, drilling and thermal cutting need no grade-specific treatment. Galvanizing is possible; agree silicon and phosphorus limits with the galvanizer if coating thickness and appearance matter. Plates for base plates, gussets and stiffeners are covered by ASTM A36 steel plate.
Delivery, Inspection and Lead Time
| Item | Specify | Reason |
|---|---|---|
| Shape | Full W designation | Nominal depth alone does not fix weight, flange width or thickness |
| Material | ASTM A36/A36M (edition if required) | The grade name must match the certificate |
| Dimensions and tolerances | ASTM A6/A6M permissible variations | Nominal catalogue values are not tolerances |
| Toughness | Charpy only if specified (A6/A6M S5 or S30) | Not required by the base specification |
| Certificate | EN 10204 3.1 or mill test report to A6/A6M | Traceability to the supplied heat |
| Mass basis | Theoretical or weighed | Avoids invoicing disputes |
Lead time: typical delivery is about 35 days for mill orders, and sizes available from stock can ship in 1–3 days. Availability is confirmed shape by shape at enquiry; the W-shape table on this page is reference geometry, not a stock list.
RFQ Checklist
- Exact W designation (e.g. W14×90 or metric W360×134), quantity and lengths in feet or metres.
- ASTM A36/A36M with edition if the project fixes one, plus any supplementary requirements (for example Charpy testing under ASTM A6/A6M S5 or S30).
- Whether a multi-certified certificate (for example A992 / A572 Gr 50 / A36) is acceptable or a single specification is required.
- Processing: cutting, coping, drilling, blasting, priming; inspection document and third-party inspection if needed.
- Packing, marking and destination; whether stock shapes for 1–3 day dispatch are preferred over a mill order.
The same W-shapes in other ASTM materials: A992, A572 Grade 50, A588 Grade B.
Frequently Asked Questions
Is A36 still used for W-shapes?
Yes, but less often. AISC lists A992 as the preferred specification for W-shapes, and some mills supply W-shapes multi-certified to A992, A572 Grade 50 and A36. A36 alone is specified where a project, a repair to an older structure or a fabrication standard calls for it.
What is the minimum yield of an A36 wide-flange beam?
36 ksi [250 MPa], with a tensile strength of 58–80 ksi [400–550 MPa]. The specification sets no maximum yield.
Which W-shapes have different A36 requirements?
Shapes with flanges over 3 in [75 mm], the jumbo W14 column sections and W40×593 in this range. They need Mn 0.85–1.35% and Si 0.15–0.40%, have no 80 ksi tensile maximum, and require 19% elongation in 2 in.
Are any W-shapes noncompact in A36?
No. At 36 ksi every W-shape in the range shown has bf/2tf below the compact limit of about 10.8. Five shapes become noncompact only at 50 ksi.
Can an A992 beam be supplied for an A36 order?
Only if the order permits it. A multi-certified report listing both A992 and A36 for the same heat satisfies an A36 order, but substituting a single-certified A992 heat requires the buyer’s acceptance.
Is A36 the same as S235JR?
No. The yield levels are close, but S235JR includes a +20 °C Charpy test and CEV limit, and European HE and IPE sections differ from W-shapes in dimensions.
Does A36 include Charpy impact testing?
Not by default. Specify A6/A6M supplementary requirement S5, or S30 for the alternate core location on heavy shapes, with temperature and energy.
What is the lead time for A36 W-shapes?
About 35 days for mill orders; shapes held in stock can ship in 1–3 days. Each designation is confirmed at enquiry.
