Q235B hot-rolled channels are open Chinese channel sections with material ordered to GB/T 700 and the rolled product series ordered to GB/T 706. This page covers the tapered inner-flange series, not a cold-formed C-section and not a relabelled European UPN or parallel-flange PFC. The open section is often attractive for edge members and bolted assemblies, provided the eccentric load path is considered.

The most consequential selection error is not always the steel grade. A load applied through a bracket on one flange can twist a single channel even when its strong-axis stress is modest. Specify the actual section, channel orientation, connection face and restraint points; a 235 MPa yield label cannot replace those details.

Order identity: keep material and section standards separate
Order fieldScope
ProductQ235B hot-rolled steel channels
Material standardGB/T 700-2006
Section/product standardGB/T 706: shape series, dimensions, tolerances and rolled-product requirements; numerical basis here 2016
Delivery conditionHot rolled; no normalized or TMCP route implied
CertificationIdentify grade, heat/batch traceability, dimensional edition and agreed test reporting

The numerical size tables on this page use GB/T 706-2016. On 22 November 2026 this is the effective edition. GB/T 706-2026 has been issued but does not take effect until 1 December 2026. These are not 2026-edition dimension tables. Specify the contractual dimensional edition, including its tolerances and mass basis, rather than silently applying a later edition to an earlier catalogue.

GB channel20a open tapered channel, 200 by 73 mm, 7 mm web, 11 mm middle flange thickness and 1:10 inner flange slope
GB channel20a open tapered channel, 200 by 73 mm, 7 mm web, 11 mm middle flange thickness and 1:10 inner flange slope. Fillet and toe radii are roll-pass-design references, not independent delivery acceptance criteria.

Selection and connection engineering

Trace the load line relative to the open section

The centroid of a channel is not at the centre of an enclosing rectangle, and its shear centre is not generally at the centroid. A transverse load or connection offset can therefore introduce torsion along with bending. Show where the load enters, how the flange or web is restrained and whether the member is allowed to twist. A simple strong-axis beam sketch is not sufficient for a flange-mounted bracket.

Make a paired-channel detail act as the design assumes

Two channels do not automatically behave as a single closed member. Spacing, orientation, battens or stitch connections and end load distribution determine whether the assembly can transfer the required forces. Check local bending at the connectors, access for bolts or welds, and the effect of eccentric single-sided attachments. Do not add two catalogue section properties without the necessary built-up-member model.

Measure the middle flange and the clear connection zone separately

Channel20a is 200 × 73 × 7 mm with an 11 mm middle flange thickness. Its inner face has a 1:10 nominal slope; the thickness at the toe is not 11 mm. Allow space for root fillets and the actual bearing surface. If a bolted detail needs a tapered washer or a shaped seat, that must be established on the connection drawing, not assumed from a PFC detail.

Agree the quantity and weight basis without overstating availability

At 22.6 kg/m, a nominal 6 m channel20a represents 135.6 kg on the reference table basis. Rolled length and mass tolerances still apply. A request should distinguish number of pieces, exact cut or ordered length and theoretical versus actual-mass settlement. The size series is a dimensional reference, not a list of channels available immediately.

Mechanical properties: identify the tested thickness

Q235B section material: thickness bands covering every listed section
Nominal material thicknessMinimum ReH, MPaRm, MPaMinimum A, %
d ≤16 mm235370–50026
16 < d ≤40 mm225370–50026

For these tables d denotes the applicable material-thickness reference: ordinarily the web in I-sections/channels and the leg in angles. It is not the overall height or leg width. Elongation values are the section/bar longitudinal reference; plate-specific specimen orientation or deductions must not be imported unchanged. Final specimen position, direction and preparation follow the ordered standards and contract, including GB/T 2975. These two bands cover the supplied reference series; they do not authorize other heavy-section products.

Ordinary GB/T 706-2016 Table 5 sampling is from the web. The 41 listed channel models have web thicknesses up to 14.5 mm, so all remain in the first yield band on that sampling reference. Middle flange thickness can be greater than web thickness. That does not change the ordinary web specimen, nor does the web result establish a uniform local flange strength for every design check.

Q235B impact quality, subject to test applicability
TemperatureLongitudinal Charpy V-notch referenceThickness and reporting qualification
+20 °C27 JOrdinary section test obligation starts at nominal thickness 12 mm; supplier-guaranteed omission below 25 mm requires buyer agreement.

Only four of the 41 listed webs reach 12 mm; most channel webs are thinner than the ordinary impact-test trigger. The B suffix is not proof that every delivered certificate contains measured impact results. Specify actual impact testing if required; use the standard’s applicable specimen and acceptance rules rather than assuming full-size specimens can be obtained from every section. B at +20 °C is not a subzero toughness qualification.

Heat chemistry and finished-product analysis

Material heat/ladle analysis: maxima in mass % unless stated otherwise
ElementLimitAcceptance note
C0.20A rise to 0.22 requires purchaser agreement; there is no carbon minimum in this edition.
Si0.35Heat-analysis maximum.
Mn1.40Maximum; do not impose the obsolete 0.30–0.70 range as the 2006 requirement.
P0.045Heat-analysis maximum.
S0.045Heat-analysis maximum.
Cr / Ni / Cu, each0.30Residual limits; analysis may be omitted when the supplier guarantees compliance.
N0.008Subject to the standard’s nitrogen/phosphorus compensation and nitrogen-binding exceptions; identify any applicable exception.
As0.080Ordinary maximum; arsenic-bearing ore arrangements require agreement.

These are material heat/ladle limits under GB/T 700-2006, not a finished-product analysis tolerance table. Q235B has no universal CEV ceiling in that standard. Where welding assessment requires carbon equivalent, agree the calculation and acceptance criterion using the actual heat chemistry rather than inventing a grade-wide cap.

Keep heat analysis and product analysis distinct. Heat/ladle results identify the melt; a test on the finished rolled section is product analysis and is assessed using the applicable GB/T 222 permitted-deviation provisions. No numerical product-analysis deviations are supplied by the compiled dataset, so no extra tolerance has been invented here. If product analysis is required, agree the sampling, test method, material edition and deviation table before ordering; do not add a discretionary percentage to every heat limit.

GB/T 706-2016 dimensions and theoretical mass

All dimensions are millimetres; A is cross-sectional area in cm² and mass is kg/m. The values are a reference series, not a stock list or a guarantee that every size/grade combination can be supplied on a particular enquiry. Confirm the actual section, length, quantity and certification requirement. The tabulated mass is retained on its published 2016 basis rather than reconstructed from rounded area values. Dimensional, shape and mass tolerances must be taken from the contracted edition, not from the number of decimal places below.

Here h is the overall depth, b the flange width, d the web thickness and t the middle flange thickness. The inside face is tapered; t is not a constant plate thickness. The final column is an ordinary web-sampling yield reference, not a member resistance or a universal flange design value.

Complete channel series, 41 models; GB/T 706-2016 reference
Modelh × b × dh mmb mmd mmt mmA cm²kg/mWeb-band ReH min, MPa
550×37×4.550374.57.06.9255.44235
6.363×40×4.863404.87.58.4466.63235
6.565×40×4.365404.37.58.2926.51235
880×43×5.080435.08.010.248.04235
10100×48×5.3100485.38.512.7410.0235
12120×53×5.5120535.59.015.3612.1235
12.6126×53×5.5126535.59.015.6912.3235
14a140×58×6.0140586.09.518.5114.5235
14b140×60×8.0140608.09.521.3116.7235
16a160×63×6.5160636.510.021.9517.2235
16b160×65×8.5160658.510.025.1519.8235
18a180×68×7.0180687.010.525.6920.2235
18b180×70×9.0180709.010.529.2923.0235
20a200×73×7.0200737.011.028.8322.6235
20b200×75×9.0200759.011.032.8325.8235
22a220×77×7.0220777.011.531.8325.0235
22b220×79×9.0220799.011.536.2328.5235
24a240×78×7.0240787.012.034.2126.9235
24b240×80×9.0240809.012.039.0130.6235
24c240×82×11.02408211.012.043.8134.4235
25a250×78×7.0250787.012.034.9127.4235
25b250×80×9.0250809.012.039.9131.3235
25c250×82×11.02508211.012.044.9135.3235
27a270×82×7.5270827.512.539.2730.8235
27b270×84×9.5270849.512.544.6735.1235
27c270×86×11.52708611.512.550.0739.3235
28a280×82×7.5280827.512.540.0231.4235
28b280×84×9.5280849.512.545.6235.8235
28c280×86×11.52808611.512.551.2240.2235
30a300×85×7.5300857.513.543.8934.5235
30b300×87×9.5300879.513.549.8939.2235
30c300×89×11.53008911.513.555.8943.9235
32a320×88×8.0320888.014.048.5038.1235
32b320×90×10.03209010.014.054.9043.1235
32c320×92×12.03209212.014.061.3048.1235
36a360×96×9.0360969.016.060.8947.8235
36b360×98×11.03609811.016.068.0953.5235
36c360×100×13.036010013.016.075.2959.1235
40a400×100×10.540010010.518.075.0458.9235
40b400×102×12.540010212.518.083.0465.2235
40c400×104×14.540010414.518.091.0471.5235

Inspection, traceability and enquiry

Check depth, flange width, web and middle-flange thickness, flange inclination, straightness and twist. For paired channels, identify orientation and matching lengths without implying that material acceptance certifies the built-up assembly.

  • State the full designation, exact grade/material edition, dimensional edition, lengths and quantity; identify any approved deviation from the normal hot-rolled scope.
  • Define the documentary requirement before ordering: heat analysis, applicable tensile results, the impact-test regime where required, and traceability between the certificate and supplied bundles. Do not assume a particular third-party certificate or inspection service.
  • Specify theoretical or actual-mass settlement and any special dimensional acceptance before quotation. Extra tests, coatings, fabrication or additional delivery conditions are not implied by a general grade enquiry.

Lead time: a typical mill order is about 35 days. Stocked sizes: 1–3 days, subject to enquiry and confirmation of the individual size, grade, quantity and delivery requirement. A tabulated section is not a statement that it is held in stock.

Related section and material comparisons

For a different rolled geometry in the same material, see Q235B H-beams. The Q235B plate material page is a separate product form: it must not replace the section-specific sampling and shape requirements above.

The parallel-flange channel family overview and S235JR UPE/PFC reference explain a different channel system. They do not turn the tapered GB channel into a PFC or establish equal mass, bolt seating or resistance.

Compare this GB/T 706 tapered channel family in the other grade: Q355B Channels.

Frequently asked questions

Are these Chinese channels UPN, UPE or PFC?

No. They use the GB/T 706 tapered channel series. UPN also has a tapered family but has different standard geometry; UPE/PFC are parallel-flange families. Match the full dimensions, material standard, tolerances and connection before approving any replacement. The family names are not interchangeable stock descriptions.

Why can a channel twist under a vertical load?

A channel is an open, singly symmetric section whose shear centre generally does not coincide with the centroid. If the load does not pass through the appropriate torsion-free load line, twisting can accompany bending. Establish the load entry point, restraint and end conditions in the structural model, including loads from flange-mounted brackets.

Can two channels be treated as one box section?

Only if the engineered arrangement and its connections justify the assumed composite action. Orientation, separation, battens or stitching and end load distribution determine the load path. Merely placing two channels together does not provide the torsional stiffness of a continuously closed section.

Is t the same as the web thickness d?

No. d is the web thickness; t is the middle flange thickness on the tapered inner face. Channel20a has d = 7 mm and t = 11 mm. The ordinary material sample is taken in the web under GB/T 706; flange bearing, bolt seating and local flange design remain separate issues.

Does Q235B always mean 235 MPa and a measured 27 J test?

No. Yield depends on the applicable material thickness; it is 235 MPa up to 16 mm and 225 MPa over 16 through 40 mm for the reference range here. The 27 J value is a +20 °C longitudinal impact requirement when the test regime applies. Thickness triggers and agreed supplier-guaranteed omissions must be considered before interpreting a certificate.

What if a finished-product chemistry test differs from the heat analysis?

First identify whether the result is a heat analysis or product analysis and which material edition and test method apply. Finished-product results use the applicable GB/T 222 permitted deviations; do not reject or accept them by silently adding a made-up allowance to the ladle table. Record the sampling and agreed acceptance basis before testing.

Can this grade be used in a welded or cold-service structure?

Neither application should be approved from the grade name alone. Welding needs actual heat chemistry, joint thickness, restraint and a suitable procedure; GB/T 700 does not supply a universal Q235B CEV ceiling. B quality is a room-temperature impact regime, not a subzero service guarantee. The project specification must set any additional toughness requirement.

What information should accompany a size enquiry?

Send the full section designation and variant, Q235B to GB/T 700-2006, the chosen GB/T 706 dimensional edition, lengths, quantity, mass-settlement basis and certificate/test requirements. Identify any actual impact testing or product analysis required. Typical mill orders are about 35 days; stocked sizes are 1–3 days only after the individual enquiry is confirmed.

For an enquiry to Gangsteel, provide the exact section and material specification, rather than a grade name alone. Quote acceptance remains subject to confirmation of the requested size, quantity and test scope.

Other Products