
EN 10025 S355M TMCP Structural Steel Plate
Gangsteel – China's Leading Mill-Direct Supplier & Exporter of EN 10025 S355M TMCP Structural Steel Plates
Gangsteel keeps the largest permanent stock of EN 10025 S355M TMCP structural steel plates in Asia – more than 4,000 tons always ready in thickness 6–200 mm, width 1500–4200 mm, length up to 18 m. All plates are genuine TMCP (thermomechanical controlled process) produced by top mills (HBIS, Shougang, Nanjing Steel) with full European approvals (PED 2014/68/EU, CPR 305/2011). We supply with original EN 10204-3.1/3.2 certificates and third-party inspection (DNV-GL, ABS, LR, BV, CCS, KR, TÜV, SGS).
S355M is the standard-temperature version of the popular EN 10025-4 series, offering 355 MPa minimum yield strength and ≥40 J impact toughness at –20 °C. It is the direct TMCP alternative to normalized S355N (EN 10025-3) and the sister grade to low-temperature S355ML.
We also stock the complete EN 10025-4 series in our en 10025 4 High Strength Structural Steel range, including the most popular low-temperature grade en 10025 4 s355ml steel plate, higher-strength en 10025 4 s420m steel plate, and top-end en 10025 4 s460m steel plate.
What is EN 10025 S355M TMCP Structural Steel Plate?
EN 10025 S355M is a thermomechanically rolled (TMCP) weldable fine-grain structural steel specified in EN 10025-4:2004 (current version 2019).
The designation breaks down as:
- S= structural steel
- 355= minimum yield strength 355 MPa (transverse, thickness ≤ 16 mm)
- M= thermomechanical rolling (TMCP delivery condition)
- No “L” = standard impact toughness ≥ 40 J at –20 °C (longitudinal)
The TMCP process – controlled hot rolling followed by accelerated cooling – produces a very fine-grained microstructure without separate normalizing heat treatment. This gives S355M:
- Lower residual stress than normalized grades
- Excellent flatness and dimensional stability
- Superior weldability (CEV ≤ 0.39)
- Better fatigue performance
S355M is the standard-temperature counterpart to the more popular low-temperature grade S355ML (–50 °C). When the service temperature stays above –20 °C, S355M is the cost-effective choice with identical strength and chemistry.
Chemical Composition – Ladle Analysis (max % unless noted)
|
Element |
C |
Si |
Mn |
P |
S |
Nb |
V |
Al min |
Ti |
Cr |
Ni |
Mo |
Cu |
N |
CEV max |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
S355M |
0.14 |
0.50 |
1.60 |
0.025 |
0.020 |
0.05 |
0.10 |
0.020 |
0.05 |
0.30 |
0.50 |
0.10 |
0.55 |
0.015 |
0.39 |
Typical Gangsteel actual values: C 0.09–0.12 %, CEV 0.34–0.37 → excellent weldability without preheating up to 80 mm thickness.
Mechanical Properties – Full Thickness Range up to 200 mm (transverse values)
|
Thickness (mm) |
ReH min (MPa) |
Rm (MPa) |
A5 min (%) |
KV min (J) at –20 °C longitudinal |
|---|---|---|---|---|
|
≤ 16 |
355 |
470–630 |
22 |
40 |
|
>16 ≤ 40 |
345 |
470–630 |
22 |
40 |
|
>40 ≤ 63 |
335 |
470–630 |
22 |
40 |
|
>63 ≤ 80 |
325 |
470–630 |
22 |
40 |
|
>80 ≤ 100 |
315 |
470–630 |
22 |
40 |
|
>100 ≤ 120 |
305 |
450–610 |
22 |
40 |
|
>120 ≤ 150 |
295 |
450–610 |
22 |
40 |
|
>150 ≤ 200 |
285–295* |
450–610 |
22 |
40 |
*Gangsteel guarantees 295 MPa up to 180 mm, 285 MPa to 200 mm.
Hardness: 140–180 HBW Density: 7.85 g/cm³
Applications of EN 10025 S355M Plates
S355M is widely used when the service temperature is above –20 °C:
- General structural engineering
- Bridges and highway structures
- Onshore wind turbine towers
- Heavy machinery bases
- Crane booms and lifting equipment
- Shipbuilding and marine structures (non-Arctic)
When the temperature drops below –20 °C, the low-temperature version en 10025 4 s355ml steel plate is required.
For higher strength requirements, see en 10025 4 s420m steel plate (420 MPa) or en 10025 4 s460m steel plate (460 MPa).
Why Choose Gangsteel for S355M Plates
- Largest S355M stock in Asia (4,000+ tons ready)
- Factory-direct price – 60–120 USD/ton lower than traders
- Full processing capability (cutting, beveling, drilling, rolling, priming)
- Z35 quality always in stock
- Immediate delivery worldwide
- Exported to 90+ countries with perfect documentation
- One-stop service – stock → processing → shipping
FAQ – Quick Answers
Q1: S355M vs S355ML difference?A: Only impact test temperature. S355M = –20 °C (≥40 J), S355ML = –50 °C (≥27 J). Strength, chemistry, weldability identical.
Q2: Preheating required?A: No preheat up to 80 mm thickness. >80 mm: 75–100 °C max.
Q3: Z35 availability?A: Yes – large stock of S355M + Z35 ready for immediate delivery.
Q4: Density and hardness?A: Density 7.85 g/cm³, hardness 140–180 HBW.
Q5: NDT standard?A: 100 % UT EN 10160 S2/E2 included. S3/E3, MT, PT on request.
Q6: Maximum thickness?A: Up to 200 mm with full properties and certification.
Q7: Delivery time?A: Stock material 3–7 days worldwide.
Contact Gangsteel Today
Need EN 10025 S355M plates? Contact us now for best price and fastest delivery.
Email: admin@gangsteel.com WhatsApp/WeChat/Mobile: +86 135 9887 9167 Website: https://gangsteel.net/
Gangsteel – Real Factory. Real Stock. Real Fast Delivery.
Other Articles for en 10025-4 s355m steel plate
- S355 Material Equivalent EN 10025-4 Supplier
- S355 Mechanical Properties EN 10025-4 Plate Supplier
- S355MC Equivalent EN 10025-4 Structural Steel Supplier
- S355 Material Properties EN 10025-4 Data Sheet Supplier
- S355 Material EN 10025-4 High Strength Plate Supplier
- S355M+Z35 EN 10025-4 Through-Thickness Plate Supplier
- S355M vs S355MC EN 10025-4 Structural vs Forming Supplier
- S355M vs S355ML EN 10025-4 Impact Comparison Supplier
- S355M vs S355J2 EN 10025-4 Strength Comparison Supplier
- S355M Properties EN 10025-4 Data Sheet Supplier
- Material S355M EN 10025-4 Thermomechanical Supplier
- S355M Meaning EN 10025-4 Structural Grade Supplier
- S355M Chemical Composition EN 10025-4 Supplier
- S355M vs S355ML EN 10025-4 Low Temp Plate Supplier
- S355M Equivalent Material EN 10025-4 Supplier
- S355M Steel Equivalent EN 10025-4 Plate Supplier
- S355M Material EN 10025-4 Fine Grain Steel Supplier
- S355M Steel EN 10025-4 Hot Rolled Plate Supplier
- S355M vs S355N EN 10025-4 Steel Plate Comparison Supplier
- EN 10025-4 S355M Weldable Fine Grain Plate Supplier
- Steel Grade S355M EN 10025-4 Structural Plate Supplier
- EN10025-4 S355M High Strength Steel Plate Supplier
- EN 10025 S355M TMCP Structural Steel Plate Supplier
-
BHW35 Steel Plate for Sale | RF
BHW35 / 13MnNiMo5-4 (DIWA 353 family): identity, chemistry, mechanical properties, related grades, and RFQ note
-
ASTM A516 Grade 70 Equivalent:
ASTM A516 Grade 70 equivalents include ASME SA516 Gr 70, EN 10028-2 P355GH and BS 1501 224-490. Gangsteel compa
-
What is the difference between
we supply high-quality A516 Gr 70 steel plate for pressure vessel applications and other standards like ASTM A2
-
P355GH AND S355J2 Steel Plates
EN10028-2 P355GH for High-Strength Low-Alloy Columbium-Vanadium Structural Steel EN10025-2 S355J2 Structural St
