
S275JR Angles: Equal and Unequal Legs in One Grade
S275JR angles sit between the light S235JR grade and the 355 MPa grades: 17% more yield than S235JR with similar weldability. Gangsteel supplies EN 10025-2 S275JR equal and unequal angles for roof and floor trusses, wind bracing, purlin cleats, crane-rail stops, platform framing and general building steelwork. Order as “L 120 × 80 × 10, EN 10025-2 S275JR”.
| Item | Value | Note |
|---|---|---|
| Material | EN 10025-2:2019 S275JR (1.0044) | Impact quality 27 J at +20 °C |
| Section series | Equal and unequal leg angles to EN 10056-1 | Hot-rolled, rounded root and toe; not for square-root angles |
| Tolerances | EN 10056-2 | Leg length, thickness, out-of-square, straightness, mass |
| General delivery | EN 10025-1 | Testing, inspection documents, marking |
| Supply | Gangsteel supplies EN 10025-2 S275JR equal and unequal angles | Sizes, quantities and stock confirmed per enquiry |
| Former designation | St 44-2 (DIN 17100, withdrawn) | Historical only |
Equal Angles in S275JR: Size Range
| Leg size mm | t mm | kg/m | ReH MPa | Thinnest Class 3 t | Class 4 thicknesses |
|---|---|---|---|---|---|
| L 25 × 25 | 3–4 | 1.12–1.45 | 275 | 3 mm | 0 |
| L 30 × 30 | 3–4 | 1.36–1.78 | 275 | 3 mm | 0 |
| L 35 × 35 | 4–5 | 2.09–2.57 | 275 | 4 mm | 0 |
| L 40 × 40 | 4–6 | 2.42–3.52 | 275 | 4 mm | 0 |
| L 45 × 45 | 3–7 | 2.09–4.6 | 275 | 4.5 mm | 2 |
| L 50 × 50 | 4–9 | 3.06–6.47 | 275 | 5 mm | 1 |
| L 55 × 55 | 4–6 | 3.38–4.95 | 275 | 6 mm | 2 |
| L 60 × 60 | 4–10 | 3.7–8.69 | 275 | 6 mm | 2 |
| L 63 × 63 | 5–6.5 | 4.82–6.17 | 275 | 6 mm | 1 |
| L 65 × 65 | 4–11 | 4.02–10.3 | 275 | 7 mm | 3 |
| L 70 × 70 | 5–10 | 5.37–10.3 | 275 | 7 mm | 2 |
| L 75 × 75 | 4–10 | 4.65–11.1 | 275 | 8 mm | 4 |
| L 80 × 80 | 5–10 | 6.17–11.9 | 275 | 8 mm | 3 |
| L 90 × 90 | 5–16 | 6.97–20.7 | 275 | 9 mm | 4 |
| L 100 × 100 | 6–18 | 9.26–26.2 | 275 / 265 | 10 mm | 4 |
| L 110 × 110 | 6–14 | 10.2–23.3 | 275 | 11 mm | 5 |
| L 120 × 120 | 7–16 | 12.9–28.3 | 275 | 12 mm | 5 |
| L 130 × 130 | 8–16 | 16–30.8 | 275 | 13 mm | 5 |
| L 140 × 140 | 9–18 | 19.3–37.2 | 275 / 265 | 14 mm | 5 |
| L 150 × 150 | 10–20 | 23–44.2 | 275 / 265 | 15 mm | 5 |
| L 160 × 160 | 12–20 | 29.3–47.3 | 275 / 265 | 16 mm | 4 |
| L 180 × 180 | 13–22 | 35.7–58.6 | 275 / 265 | 17 mm | 4 |
| L 200 × 200 | 12–28 | 36.8–82 | 275 / 265 | 19 mm | 7 |
| L 250 × 250 | 17–35 | 64.4–128 | 265 | 24 mm | 7 |
| L 300 × 300 | 25–35 | 112–154 | 265 | 28 mm | 3 |
The range covers 25 × 25 to 300 × 300 mm. Some sizes and thicknesses are specific to individual mills rather than listed in EN 10056-1, so name the full designation, for example L 100 × 100 × 10, and confirm the size at enquiry.
Equal Angle Properties in S275JR
| Designation | kg/m | A cm² | c cm | Iy = Iz cm⁴ | iv cm | Wel cm³ | ReH MPa | A·ReH kN | Class, axial |
|---|---|---|---|---|---|---|---|---|---|
| L 25 × 25 × 3 | 1.12 | 1.42 | 0.720 | 0.800 | 0.480 | 0.450 | 275 | 39 | Class 3 |
| L 30 × 30 × 3 | 1.36 | 1.74 | 0.840 | 1.40 | 0.580 | 0.650 | 275 | 48 | Class 3 |
| L 35 × 35 × 4 | 2.09 | 2.67 | 1.00 | 2.95 | 0.680 | 1.18 | 275 | 73 | Class 3 |
| L 40 × 40 × 4 | 2.42 | 3.08 | 1.12 | 4.47 | 0.780 | 1.55 | 275 | 85 | Class 3 |
| L 45 × 45 × 4.5 | 3.06 | 3.90 | 1.25 | 7.14 | 0.870 | 2.20 | 275 | 107 | Class 3 |
| L 50 × 50 × 5 | 3.77 | 4.80 | 1.40 | 11.0 | 0.970 | 3.05 | 275 | 132 | Class 3 |
| L 55 × 55 × 6 | 4.95 | 6.31 | 1.56 | 17.3 | 1.06 | 4.39 | 275 | 174 | Class 3 |
| L 60 × 60 × 6 | 5.42 | 6.91 | 1.69 | 22.8 | 1.17 | 5.29 | 275 | 190 | Class 3 |
| L 63 × 63 × 6.5 | 6.17 | 7.85 | 1.78 | 28.4 | 1.22 | 6.27 | 275 | 216 | Class 3 |
| L 65 × 65 × 7 | 6.83 | 8.70 | 1.85 | 33.4 | 1.26 | 7.18 | 275 | 239 | Class 3 |
| L 70 × 70 × 7 | 7.38 | 9.40 | 1.97 | 42.3 | 1.36 | 8.41 | 275 | 258 | Class 3 |
| L 75 × 75 × 8 | 8.99 | 11.4 | 2.14 | 59.1 | 1.46 | 11.0 | 275 | 314 | Class 3 |
| L 80 × 80 × 8 | 9.63 | 12.3 | 2.26 | 72.2 | 1.56 | 12.6 | 275 | 338 | Class 3 |
| L 90 × 90 × 9 | 12.2 | 15.5 | 2.54 | 116 | 1.76 | 17.9 | 275 | 426 | Class 3 |
| L 100 × 100 × 10 | 15.0 | 19.2 | 2.82 | 177 | 1.95 | 24.6 | 275 | 528 | Class 3 |
| L 110 × 110 × 11 | 18.2 | 23.2 | 3.11 | 259 | 2.14 | 32.8 | 275 | 638 | Class 3 |
| L 120 × 120 × 12 | 21.6 | 27.5 | 3.40 | 368 | 2.35 | 42.7 | 275 | 756 | Class 3 |
| L 130 × 130 × 13 | 25.4 | 32.3 | 3.68 | 506 | 2.54 | 54.4 | 275 | 888 | Class 3 |
| L 140 × 140 × 14 | 29.4 | 37.5 | 3.96 | 681 | 2.73 | 67.9 | 275 | 1031 | Class 3 |
| L 150 × 150 × 15 | 33.8 | 43.0 | 4.25 | 898 | 2.93 | 83.5 | 275 | 1182 | Class 3 |
| L 160 × 160 × 16 | 38.4 | 49.0 | 4.53 | 1,160 | 3.12 | 101 | 275 | 1348 | Class 3 |
| L 180 × 180 × 18 | 48.6 | 61.9 | 5.10 | 1,870 | 3.52 | 145 | 265 | 1640 | Class 3 |
| L 200 × 200 × 20 | 59.9 | 76.3 | 5.68 | 2,850 | 3.92 | 199 | 265 | 2022 | Class 3 |
| L 250 × 250 × 25 | 93.2 | 119.0 | 7.11 | 6,920 | 4.89 | 387 | 265 | 3154 | Class 3 |
| L 300 × 300 × 30 | 133 | 170.0 | 8.54 | 14,300 | 5.86 | 666 | 265 | 4505 | Class 3 |
Unequal Angles in S275JR
| Designation | kg/m | A cm² | cy cm | cz cm | Iy cm⁴ | Iz cm⁴ | iv cm | tan α | ReH MPa | A·ReH kN | Class, axial |
|---|---|---|---|---|---|---|---|---|---|---|---|
| L 100 × 65 × 7 | 8.77 | 11.2 | 3.23 | 1.51 | 113 | 37.6 | 1.40 | 0.415 | 275 | 308 | Class 4 |
| L 100 × 65 × 8 | 9.94 | 12.7 | 3.27 | 1.55 | 127 | 42.2 | 1.40 | 0.413 | 275 | 349 | Class 3 |
| L 100 × 65 × 9 | 11.1 | 14.1 | 3.32 | 1.59 | 141 | 46.7 | 1.39 | 0.412 | 275 | 388 | Class 3 |
| L 100 × 65 × 10 | 12.3 | 15.6 | 3.36 | 1.63 | 154 | 51.0 | 1.39 | 0.410 | 275 | 429 | Class 3 |
| L 100 × 65 × 11 | 13.4 | 17.0 | 3.40 | 1.67 | 167 | 55.1 | 1.38 | 0.408 | 275 | 468 | Class 3 |
| L 100 × 65 × 12 | 14.5 | 18.5 | 3.44 | 1.71 | 180 | 59.1 | 1.38 | 0.406 | 275 | 509 | Class 3 |
| L 110 × 70 × 10 | 13.4 | 17.1 | 3.69 | 1.72 | 207 | 65.1 | 1.50 | 0.396 | 275 | 470 | Class 3 |
| L 110 × 70 × 12 | 15.9 | 20.3 | 3.77 | 1.79 | 242 | 75.5 | 1.49 | 0.392 | 275 | 558 | Class 3 |
| L 120 × 80 × 8 | 12.2 | 15.5 | 3.83 | 1.87 | 226 | 80.8 | 1.74 | 0.437 | 275 | 426 | Class 4 |
| L 120 × 80 × 10 | 15.0 | 19.1 | 3.92 | 1.95 | 276 | 98.1 | 1.72 | 0.435 | 275 | 525 | Class 3 |
| L 120 × 80 × 12 | 17.8 | 22.7 | 4.00 | 2.03 | 323 | 114 | 1.71 | 0.431 | 275 | 624 | Class 3 |
| L 130 × 90 × 10 | 16.6 | 21.2 | 4.16 | 2.19 | 360 | 142 | 1.94 | 0.469 | 275 | 583 | Class 4 |
| L 130 × 90 × 12 | 19.7 | 25.1 | 4.24 | 2.26 | 420 | 164 | 1.93 | 0.467 | 275 | 690 | Class 3 |
| L 130 × 90 × 14 | 22.8 | 29.0 | 4.33 | 2.34 | 481 | 188 | 1.93 | 0.463 | 275 | 798 | Class 3 |
| L 140 × 90 × 8 | 14.0 | 17.9 | 4.49 | 2.03 | 360 | 118 | 1.96 | 0.411 | 275 | 492 | Class 4 |
| L 140 × 90 × 10 | 17.4 | 22.1 | 4.58 | 2.11 | 441 | 144 | 1.95 | 0.409 | 275 | 608 | Class 4 |
| L 140 × 90 × 12 | 20.6 | 26.3 | 4.66 | 2.19 | 518 | 168 | 1.94 | 0.406 | 275 | 723 | Class 3 |
| L 140 × 90 × 14 | 23.8 | 30.4 | 4.74 | 2.27 | 592 | 191 | 1.93 | 0.403 | 275 | 836 | Class 3 |
| L 150 × 90 × 10 | 18.2 | 23.2 | 5.00 | 2.04 | 533 | 146 | 1.95 | 0.360 | 275 | 638 | Class 4 |
| L 150 × 90 × 11 | 19.9 | 25.3 | 5.04 | 2.08 | 581 | 159 | 1.94 | 0.359 | 275 | 696 | Class 4 |
| L 150 × 90 × 12 | 21.6 | 27.5 | 5.08 | 2.12 | 627 | 171 | 1.94 | 0.358 | 275 | 756 | Class 3 |
| L 150 × 100 × 10 | 19.0 | 24.2 | 4.81 | 2.34 | 553 | 199 | 2.17 | 0.438 | 275 | 666 | Class 4 |
| L 150 × 100 × 12 | 22.5 | 28.7 | 4.89 | 2.42 | 651 | 233 | 2.16 | 0.436 | 275 | 789 | Class 3 |
| L 150 × 100 × 14 | 26.1 | 33.2 | 4.98 | 2.50 | 744 | 265 | 2.15 | 0.434 | 275 | 913 | Class 3 |
| L 200 × 100 × 10 | 23.0 | 29.2 | 6.93 | 2.01 | 1,220 | 210 | 2.15 | 0.263 | 275 | 803 | Class 4 |
| L 200 × 100 × 12 | 27.3 | 34.8 | 7.03 | 2.10 | 1,440 | 247 | 2.14 | 0.262 | 275 | 957 | Class 4 |
| L 200 × 100 × 14 | 31.6 | 40.3 | 7.12 | 2.18 | 1,650 | 282 | 2.12 | 0.261 | 275 | 1108 | Class 4 |
| L 200 × 100 × 15 | 33.8 | 43.0 | 7.16 | 2.22 | 1,760 | 299 | 2.12 | 0.260 | 275 | 1182 | Class 3 |
| L 200 × 100 × 16 | 35.9 | 45.7 | 7.20 | 2.26 | 1,860 | 316 | 2.11 | 0.258 | 275 | 1257 | Class 3 |
| L 250 × 90 × 12 | 31.2 | 39.7 | 9.50 | 1.64 | 2,560 | 187 | 1.81 | 0.152 | 275 | 1092 | Class 4 |
| L 250 × 90 × 14 | 36.1 | 46.0 | 9.60 | 1.72 | 2,950 | 214 | 1.80 | 0.151 | 275 | 1265 | Class 4 |
| L 250 × 90 × 16 | 40.9 | 52.1 | 9.70 | 1.81 | 3,330 | 239 | 1.79 | 0.149 | 275 | 1433 | Class 4 |
Legs up to 16 mm are rated at 275 MPa and thicker legs at 265 MPa. With ε = 0.92 the leg/10 proportion still passes as Class 3, because 11.5ε is about 10.6 at 275 MPa: L 100 × 100 × 10 and L 80 × 80 × 8 remain non-slender. Thinner proportions cross into Class 4 sooner than in S235JR; for example L 100 × 100 now needs t ≥ 10 mm, against 9 mm in S235JR. In total 78 equal thicknesses and 14 unequal angles are Class 4 in S275JR.
A·ReH is the gross characteristic squash load (gross area × yield). It is not a design resistance: it ignores partial factors, flexural and flexural-torsional buckling, the eccentricity of end connections, net-section effects at bolt holes and, for Class 4 sections, the reduced effective area. The class uses the EN 1993-1-1 rule for angles in compression: Class 3 when h/t ≤ 15ε and (b + h)/(2t) ≤ 11.5ε, otherwise Class 4, with ε = √(235/ReH). Angles do not reach Class 1 or 2 under this rule. Confirm with the design code and national annex used on the project.
S275JR Chemistry for Angle Sections
| Element | t ≤ 30 mm | 30 mm < t ≤ 40 mm (L 250 and L 300, t 31–35) |
|---|---|---|
| C | 0.21 | 0.21 |
| Mn | 1.50 | 1.50 |
| Si | no maximum in grade row | no maximum in grade row |
| P / S | 0.040 / 0.040 | 0.040 / 0.040 |
| N | 0.012 (waived with total Al ≥ 0.020% or reported N-binding elements) | 0.012 |
| Cu | 0.55 | 0.55 |
| CEV | 0.40 | 0.40 |
S275JR allows 0.21% carbon and a CEV of 0.40% across the full angle thickness range, with no change at 30 mm. Silicon has no maximum, so request the galvanizing range if needed.
S275JR Tensile and Impact Requirements
| Property | t ≤ 16 mm | 16 mm < t ≤ 40 mm |
|---|---|---|
| Minimum ReH | 275 MPa | 265 MPa |
| Rm (3 ≤ t ≤ 100 mm) | 410–560 MPa | 410–560 MPa |
| Minimum A (L0 = 5.65√S0) | 23% | 23% |
| Charpy V, minimum | 27 J at +20 °C | 27 J at +20 °C |
| Angles in this band | All unequal sizes; equal sizes up to t = 16 | Equal angles L 100 × 100 × 18 and L 150 to L 300 above 16 mm |
The +20 °C impact quality suits enclosed buildings. Exposed lattice structures in cold regions normally need S275J0, S275J2 or a 355 MPa J2 grade; these are separate grades with their own certificates.
Designing with S275JR Angles
In trusses, S275JR angles are often used as double angles back-to-back for chords and as single angles for web members. For single angles connected through one leg, the end eccentricity and the weak v-v axis dominate, so the extra yield mainly helps stocky members and members in tension. Example: L 120 × 80 × 10 has A = 19.1 cm²; its gross squash load is about 525 kN at 275 MPa, but a single bolted leg reduces the effective net area under EN 1993-1-8.
For unequal angles the principal axes are rotated by α from the leg axes (tan α between about 0.15 and 0.47 in this table), so the long leg should be placed to suit the bending direction. Connecting the long leg usually gives better net-section efficiency for tension members.
S275JR Compared with Other Angle Grades
| Grade | Thinnest Class 3 L 100 × 100 | Thinnest Class 3 L 150 × 150 | Equal sizes Class 4 (of 192) |
|---|---|---|---|
| S235JR | 9 mm | 14 mm | 58 |
| S275JR | 10 mm | 15 mm | 78 |
| S355JR / S355J2 | 11 mm | 17 mm | 109 |
Fabrication: Bolting, Welding and Galvanizing
Welding S275JR angles rarely needs preheat at CEV ≤ 0.40%. Avoid welding across the toe radius where the leg is thinnest. When angles are coped or notched to clear flanges, keep a radius at the re-entrant corner. Galvanized lattice members should be drilled or punched before coating; seal back-to-back gaps or leave them wide enough for zinc drainage.
Delivery Condition, Inspection and Lead Time
| Item | Specify | Reason |
|---|---|---|
| Designation | L h × b × t, e.g. L 150 × 90 × 10 | Leg lengths alone do not fix thickness or mass |
| Delivery condition | +AR or +N where required | Not implied by the grade name |
| Impact test | Whether the 27 J at +20 °C result must be reported, and specimen size for thin legs | Angle legs run from 3 to 35 mm |
| Inspection document | EN 10204 3.1 for heat-specific results | Traceability to the delivered pieces |
| Dimensions | EN 10056-2 tolerances, lengths, cut list | Nominal values are not tolerances |
| Mass basis | Theoretical or weighed | Avoids invoicing disputes |
Lead time: typical delivery is about 35 days for mill orders, and sizes available from stock can ship in 1–3 days. Stock is confirmed size by size at enquiry; the angle tables on this page are reference geometry, not a stock list.
RFQ Checklist
- Full angle designation, quantity and lengths; equal and unequal sizes listed separately.
- EN 10025-2 S275JR, delivery condition and any chemistry options such as the galvanizing silicon range.
- Impact verification and EN 10204 document type.
- Processing: cutting, punching or drilling of legs, notching, galvanizing.
- Packing, marking and destination; whether stock sizes for 1–3 day dispatch are preferred over a mill order.
Other sections in the same grade: EN 10025-2 S275JR HEA and HEB beams, EN 10025-2 S275JR IPE beams and EN 10025-2 S275JR UPE and PFC channels. The hot-rolled steel angle range overview covers angles across grades, gussets and cleat plates are covered by EN 10025-2 S275JR steel plate, and the structural steel sections guide compares all section families.
The same equal and unequal angles in other EN 10025-2 grades: S235JR angles, S355JR angles, S355J2 angles.
Frequently Asked Questions
Which S275JR angles are rated at 265 MPa?
Equal angles with legs over 16 mm thick: L 100 × 100 × 18 and the heavier L 150 to L 300 sizes. All other angles, including every unequal size in the table, are rated at 275 MPa.
Is L 100 × 100 × 10 Class 3 or Class 4 in S275JR?
Class 3. Its ratio (b + h)/(2t) = 10 is below 11.5ε (about 10.6), and h/t = 10 is below 15ε.
Why do unequal angles turn Class 4 more often?
The long leg drives h/t, and the limit h/t ≤ 15ε is about 13.9 in S275JR. Thin long-leg shapes such as L 200 × 100 × 10 and L 250 × 90 × 12 exceed it.
Is S275JR the successor to St 44-2?
Yes, it is the EN 10025-2 grade generally used where St 44-2 was specified under the withdrawn DIN 17100. Certificates will show EN 10025-2:2019 S275JR.
Should truss web members be single or double S275JR angles?
Single angles are cheap and easy to connect but loaded eccentrically and weak about v-v; double angles are symmetric and stronger in compression. The choice depends on force, length and connection detail.
Do S275JR angles need impact testing?
The grade includes a 27 J test at +20 °C. Legs below about 11 mm only allow sub-size specimens, and 3–5 mm legs are below the usual specimen range, so agree the reporting for light angles.
Which leg of an unequal S275JR angle should be connected?
For tension members, connecting the long leg usually reduces shear-lag losses. For compression, follow the design model in the applicable code; the principal axes are inclined at α to the legs.
How long does an S275JR angle order take?
About 35 days for mill orders, 1–3 days for stock sizes. Stock is confirmed size by size.
