
S355JR Angles: Equal and Unequal Legs in One Grade
Gangsteel supplies EN 10025-2 S355JR equal and unequal angles for heavily loaded truss chords and diagonals, lattice towers, industrial bracing, crane-runway restraints and equipment frames where strength governs and the structure is enclosed or not exposed to low temperatures. Order as “L 150 × 150 × 15, EN 10025-2 S355JR”.
| Item | Value | Note |
|---|---|---|
| Material | EN 10025-2:2019 S355JR (1.0045) | Impact quality 27 J at +20 °C |
| Section series | Equal and unequal leg angles to EN 10056-1 | Hot-rolled, rounded root and toe; not for square-root angles |
| Tolerances | EN 10056-2 | Leg length, thickness, out-of-square, straightness, mass |
| General delivery | EN 10025-1 | Testing, inspection documents, marking |
| Supply | Gangsteel supplies EN 10025-2 S355JR equal and unequal angles | Sizes, quantities and stock confirmed per enquiry |
| Former designation | St 52-3 was the closest DIN 17100 grade but required −20 °C impact; S355JR is not its direct equivalent | Check old drawings |
Equal Angles in S355JR: Size Range
| Leg size mm | t mm | kg/m | ReH MPa | Thinnest Class 3 t | Class 4 thicknesses |
|---|---|---|---|---|---|
| L 25 × 25 | 3–4 | 1.12–1.45 | 355 | 3 mm | 0 |
| L 30 × 30 | 3–4 | 1.36–1.78 | 355 | 4 mm | 1 |
| L 35 × 35 | 4–5 | 2.09–2.57 | 355 | 4 mm | 0 |
| L 40 × 40 | 4–6 | 2.42–3.52 | 355 | 5 mm | 1 |
| L 45 × 45 | 3–7 | 2.09–4.6 | 355 | 5 mm | 3 |
| L 50 × 50 | 4–9 | 3.06–6.47 | 355 | 6 mm | 2 |
| L 55 × 55 | 4–6 | 3.38–4.95 | 355 | 6 mm | 2 |
| L 60 × 60 | 4–10 | 3.7–8.69 | 355 | 7 mm | 3 |
| L 63 × 63 | 5–6.5 | 4.82–6.17 | 355 | none | 3 |
| L 65 × 65 | 4–11 | 4.02–10.3 | 355 | 7 mm | 3 |
| L 70 × 70 | 5–10 | 5.37–10.3 | 355 | 8 mm | 3 |
| L 75 × 75 | 4–10 | 4.65–11.1 | 355 | 9 mm | 5 |
| L 80 × 80 | 5–10 | 6.17–11.9 | 355 | 9 mm | 4 |
| L 90 × 90 | 5–16 | 6.97–20.7 | 355 | 10 mm | 5 |
| L 100 × 100 | 6–18 | 9.26–26.2 | 355 / 345 | 11 mm | 5 |
| L 110 × 110 | 6–14 | 10.2–23.3 | 355 | 12 mm | 6 |
| L 120 × 120 | 7–16 | 12.9–28.3 | 355 | 13 mm | 6 |
| L 130 × 130 | 8–16 | 16–30.8 | 355 | 14 mm | 6 |
| L 140 × 140 | 9–18 | 19.3–37.2 | 355 / 345 | 15 mm | 6 |
| L 150 × 150 | 10–20 | 23–44.2 | 355 / 345 | 17 mm | 7 |
| L 160 × 160 | 12–20 | 29.3–47.3 | 355 / 345 | 17 mm | 5 |
| L 180 × 180 | 13–22 | 35.7–58.6 | 355 / 345 | 19 mm | 6 |
| L 200 × 200 | 12–28 | 36.8–82 | 355 / 345 | 22 mm | 10 |
| L 250 × 250 | 17–35 | 64.4–128 | 345 | 27 mm | 10 |
| L 300 × 300 | 25–35 | 112–154 | 345 | 32 mm | 7 |
The range covers 25 × 25 to 300 × 300 mm. Some sizes and thicknesses are specific to individual mills rather than listed in EN 10056-1, so name the full designation, for example L 100 × 100 × 10, and confirm the size at enquiry.
Equal Angle Properties in S355JR
| Designation | kg/m | A cm² | c cm | Iy = Iz cm⁴ | iv cm | Wel cm³ | ReH MPa | A·ReH kN | Class, axial |
|---|---|---|---|---|---|---|---|---|---|
| L 25 × 25 × 3 | 1.12 | 1.42 | 0.720 | 0.800 | 0.480 | 0.450 | 355 | 50 | Class 3 |
| L 30 × 30 × 3 | 1.36 | 1.74 | 0.840 | 1.40 | 0.580 | 0.650 | 355 | 62 | Class 4 |
| L 35 × 35 × 4 | 2.09 | 2.67 | 1.00 | 2.95 | 0.680 | 1.18 | 355 | 95 | Class 3 |
| L 40 × 40 × 4 | 2.42 | 3.08 | 1.12 | 4.47 | 0.780 | 1.55 | 355 | 109 | Class 4 |
| L 45 × 45 × 4.5 | 3.06 | 3.90 | 1.25 | 7.14 | 0.870 | 2.20 | 355 | 138 | Class 4 |
| L 50 × 50 × 5 | 3.77 | 4.80 | 1.40 | 11.0 | 0.970 | 3.05 | 355 | 170 | Class 4 |
| L 55 × 55 × 6 | 4.95 | 6.31 | 1.56 | 17.3 | 1.06 | 4.39 | 355 | 224 | Class 3 |
| L 60 × 60 × 6 | 5.42 | 6.91 | 1.69 | 22.8 | 1.17 | 5.29 | 355 | 245 | Class 4 |
| L 63 × 63 × 6.5 | 6.17 | 7.85 | 1.78 | 28.4 | 1.22 | 6.27 | 355 | 279 | Class 4 |
| L 65 × 65 × 7 | 6.83 | 8.70 | 1.85 | 33.4 | 1.26 | 7.18 | 355 | 309 | Class 3 |
| L 70 × 70 × 7 | 7.38 | 9.40 | 1.97 | 42.3 | 1.36 | 8.41 | 355 | 334 | Class 4 |
| L 75 × 75 × 8 | 8.99 | 11.4 | 2.14 | 59.1 | 1.46 | 11.0 | 355 | 405 | Class 4 |
| L 80 × 80 × 8 | 9.63 | 12.3 | 2.26 | 72.2 | 1.56 | 12.6 | 355 | 437 | Class 4 |
| L 90 × 90 × 9 | 12.2 | 15.5 | 2.54 | 116 | 1.76 | 17.9 | 355 | 550 | Class 4 |
| L 100 × 100 × 10 | 15.0 | 19.2 | 2.82 | 177 | 1.95 | 24.6 | 355 | 682 | Class 4 |
| L 110 × 110 × 11 | 18.2 | 23.2 | 3.11 | 259 | 2.14 | 32.8 | 355 | 824 | Class 4 |
| L 120 × 120 × 12 | 21.6 | 27.5 | 3.40 | 368 | 2.35 | 42.7 | 355 | 976 | Class 4 |
| L 130 × 130 × 13 | 25.4 | 32.3 | 3.68 | 506 | 2.54 | 54.4 | 355 | 1147 | Class 4 |
| L 140 × 140 × 14 | 29.4 | 37.5 | 3.96 | 681 | 2.73 | 67.9 | 355 | 1331 | Class 4 |
| L 150 × 150 × 15 | 33.8 | 43.0 | 4.25 | 898 | 2.93 | 83.5 | 355 | 1526 | Class 4 |
| L 160 × 160 × 16 | 38.4 | 49.0 | 4.53 | 1,160 | 3.12 | 101 | 355 | 1740 | Class 4 |
| L 180 × 180 × 18 | 48.6 | 61.9 | 5.10 | 1,870 | 3.52 | 145 | 345 | 2136 | Class 4 |
| L 200 × 200 × 20 | 59.9 | 76.3 | 5.68 | 2,850 | 3.92 | 199 | 345 | 2632 | Class 4 |
| L 250 × 250 × 25 | 93.2 | 119.0 | 7.11 | 6,920 | 4.89 | 387 | 345 | 4106 | Class 4 |
| L 300 × 300 × 30 | 133 | 170.0 | 8.54 | 14,300 | 5.86 | 666 | 345 | 5865 | Class 4 |
Unequal Angles in S355JR
| Designation | kg/m | A cm² | cy cm | cz cm | Iy cm⁴ | Iz cm⁴ | iv cm | tan α | ReH MPa | A·ReH kN | Class, axial |
|---|---|---|---|---|---|---|---|---|---|---|---|
| L 100 × 65 × 7 | 8.77 | 11.2 | 3.23 | 1.51 | 113 | 37.6 | 1.40 | 0.415 | 355 | 398 | Class 4 |
| L 100 × 65 × 8 | 9.94 | 12.7 | 3.27 | 1.55 | 127 | 42.2 | 1.40 | 0.413 | 355 | 451 | Class 4 |
| L 100 × 65 × 9 | 11.1 | 14.1 | 3.32 | 1.59 | 141 | 46.7 | 1.39 | 0.412 | 355 | 501 | Class 3 |
| L 100 × 65 × 10 | 12.3 | 15.6 | 3.36 | 1.63 | 154 | 51.0 | 1.39 | 0.410 | 355 | 554 | Class 3 |
| L 100 × 65 × 11 | 13.4 | 17.0 | 3.40 | 1.67 | 167 | 55.1 | 1.38 | 0.408 | 355 | 604 | Class 3 |
| L 100 × 65 × 12 | 14.5 | 18.5 | 3.44 | 1.71 | 180 | 59.1 | 1.38 | 0.406 | 355 | 657 | Class 3 |
| L 110 × 70 × 10 | 13.4 | 17.1 | 3.69 | 1.72 | 207 | 65.1 | 1.50 | 0.396 | 355 | 607 | Class 3 |
| L 110 × 70 × 12 | 15.9 | 20.3 | 3.77 | 1.79 | 242 | 75.5 | 1.49 | 0.392 | 355 | 721 | Class 3 |
| L 120 × 80 × 8 | 12.2 | 15.5 | 3.83 | 1.87 | 226 | 80.8 | 1.74 | 0.437 | 355 | 550 | Class 4 |
| L 120 × 80 × 10 | 15.0 | 19.1 | 3.92 | 1.95 | 276 | 98.1 | 1.72 | 0.435 | 355 | 678 | Class 4 |
| L 120 × 80 × 12 | 17.8 | 22.7 | 4.00 | 2.03 | 323 | 114 | 1.71 | 0.431 | 355 | 806 | Class 3 |
| L 130 × 90 × 10 | 16.6 | 21.2 | 4.16 | 2.19 | 360 | 142 | 1.94 | 0.469 | 355 | 753 | Class 4 |
| L 130 × 90 × 12 | 19.7 | 25.1 | 4.24 | 2.26 | 420 | 164 | 1.93 | 0.467 | 355 | 891 | Class 3 |
| L 130 × 90 × 14 | 22.8 | 29.0 | 4.33 | 2.34 | 481 | 188 | 1.93 | 0.463 | 355 | 1030 | Class 3 |
| L 140 × 90 × 8 | 14.0 | 17.9 | 4.49 | 2.03 | 360 | 118 | 1.96 | 0.411 | 355 | 635 | Class 4 |
| L 140 × 90 × 10 | 17.4 | 22.1 | 4.58 | 2.11 | 441 | 144 | 1.95 | 0.409 | 355 | 785 | Class 4 |
| L 140 × 90 × 12 | 20.6 | 26.3 | 4.66 | 2.19 | 518 | 168 | 1.94 | 0.406 | 355 | 934 | Class 4 |
| L 140 × 90 × 14 | 23.8 | 30.4 | 4.74 | 2.27 | 592 | 191 | 1.93 | 0.403 | 355 | 1079 | Class 3 |
| L 150 × 90 × 10 | 18.2 | 23.2 | 5.00 | 2.04 | 533 | 146 | 1.95 | 0.360 | 355 | 824 | Class 4 |
| L 150 × 90 × 11 | 19.9 | 25.3 | 5.04 | 2.08 | 581 | 159 | 1.94 | 0.359 | 355 | 898 | Class 4 |
| L 150 × 90 × 12 | 21.6 | 27.5 | 5.08 | 2.12 | 627 | 171 | 1.94 | 0.358 | 355 | 976 | Class 4 |
| L 150 × 100 × 10 | 19.0 | 24.2 | 4.81 | 2.34 | 553 | 199 | 2.17 | 0.438 | 355 | 859 | Class 4 |
| L 150 × 100 × 12 | 22.5 | 28.7 | 4.89 | 2.42 | 651 | 233 | 2.16 | 0.436 | 355 | 1019 | Class 4 |
| L 150 × 100 × 14 | 26.1 | 33.2 | 4.98 | 2.50 | 744 | 265 | 2.15 | 0.434 | 355 | 1179 | Class 3 |
| L 200 × 100 × 10 | 23.0 | 29.2 | 6.93 | 2.01 | 1,220 | 210 | 2.15 | 0.263 | 355 | 1037 | Class 4 |
| L 200 × 100 × 12 | 27.3 | 34.8 | 7.03 | 2.10 | 1,440 | 247 | 2.14 | 0.262 | 355 | 1235 | Class 4 |
| L 200 × 100 × 14 | 31.6 | 40.3 | 7.12 | 2.18 | 1,650 | 282 | 2.12 | 0.261 | 355 | 1431 | Class 4 |
| L 200 × 100 × 15 | 33.8 | 43.0 | 7.16 | 2.22 | 1,760 | 299 | 2.12 | 0.260 | 355 | 1526 | Class 4 |
| L 200 × 100 × 16 | 35.9 | 45.7 | 7.20 | 2.26 | 1,860 | 316 | 2.11 | 0.258 | 355 | 1622 | Class 4 |
| L 250 × 90 × 12 | 31.2 | 39.7 | 9.50 | 1.64 | 2,560 | 187 | 1.81 | 0.152 | 355 | 1409 | Class 4 |
| L 250 × 90 × 14 | 36.1 | 46.0 | 9.60 | 1.72 | 2,950 | 214 | 1.80 | 0.151 | 355 | 1633 | Class 4 |
| L 250 × 90 × 16 | 40.9 | 52.1 | 9.70 | 1.81 | 3,330 | 239 | 1.79 | 0.149 | 355 | 1850 | Class 4 |
Legs up to 16 mm are rated at 355 MPa and legs from 16 to 40 mm at 345 MPa. The higher strength makes local buckling more critical: at ε = 0.81 the limit (b + h)/(2t) ≤ 11.5ε is about 9.3, so the common leg/10 proportion (L 50 × 50 × 5, L 100 × 100 × 10, L 150 × 150 × 15) is Class 4 in S355JR. L 100 × 100 needs t ≥ 11 mm and L 150 × 150 needs t ≥ 17 mm to be Class 3. Overall 109 of 192 equal thicknesses and 21 of 32 unequal angles are Class 4, so effective-area calculations are routine for this grade.
A·ReH is the gross characteristic squash load (gross area × yield). It is not a design resistance: it ignores partial factors, flexural and flexural-torsional buckling, the eccentricity of end connections, net-section effects at bolt holes and, for Class 4 sections, the reduced effective area. The class uses the EN 1993-1-1 rule for angles in compression: Class 3 when h/t ≤ 15ε and (b + h)/(2t) ≤ 11.5ε, otherwise Class 4, with ε = √(235/ReH). Angles do not reach Class 1 or 2 under this rule. Confirm with the design code and national annex used on the project.
S355JR Chemistry for Angle Sections
| Element | t ≤ 30 mm | 30 mm < t ≤ 40 mm (L 250 and L 300, t 31–35) |
|---|---|---|
| C | 0.24 | 0.24 |
| Mn | 1.60 | 1.60 |
| Si | 0.55 | 0.55 |
| P / S | 0.040 / 0.040 | 0.040 / 0.040 |
| N | 0.012 (waived with total Al ≥ 0.020% or reported N-binding elements) | 0.012 |
| Cu | 0.55 | 0.55 |
| CEV | 0.45 | 0.47 |
Carbon may be up to 0.24% and CEV 0.45% for legs up to 30 mm. For the heavy L 250 × 250 and L 300 × 300 at 31–35 mm sizes the CEV ceiling rises to 0.47%, which matters for preheat in welded connections. Silicon is capped at 0.55%.
S355JR Tensile and Impact Requirements
| Property | t ≤ 16 mm | 16 mm < t ≤ 40 mm |
|---|---|---|
| Minimum ReH | 355 MPa | 345 MPa |
| Rm (3 ≤ t ≤ 100 mm) | 470–630 MPa | 470–630 MPa |
| Minimum A (L0 = 5.65√S0) | 22% | 22% |
| Charpy V, minimum | 27 J at +20 °C | 27 J at +20 °C |
| Angles in this band | All unequal sizes; equal sizes up to t = 16 | Equal angles L 100 × 100 × 18 and L 150 to L 300 above 16 mm |
The 27 J impact test is at +20 °C. For exposed towers and outdoor frames in cold climates, S355J0 or S355J2 is usually specified instead.
Designing with S355JR Angles
Higher yield pays off most in tension members and in stocky compression members. Gross squash load rises to about 682 kN for L 100 × 100 × 10, but because that angle is Class 4 in this grade, its compression resistance uses an effective area smaller than 19.2 cm². For slender single angles, buckling about v-v (iv = 1.95 cm for L 100 × 100 × 10) limits the benefit further. Thicker legs, double angles and star-battened pairs make better use of S355JR in compression.
Lattice tower legs, which are typically equal angles with diagonals bolted to both legs, are often designed to specific tower codes; check that the code accepts EN 10025-2 S355JR and its impact quality for the site climate.
S355JR Compared with Other Angle Grades
| Grade | L 100 × 100 × 10 class | Unequal angles Class 4 (of 32) | CEV above 30 mm |
|---|---|---|---|
| S235JR | Class 3 | 10 | 0.35 |
| S275JR | Class 3 | 14 | 0.40 |
| S355JR | Class 4 | 21 | 0.47 |
| S355J2 | Class 4 | 21 | 0.47 |
Fabrication: Bolting, Welding and Galvanizing
Weld S355JR angles to a qualified procedure with matching consumables. Preheat depends on CEV, combined thickness and hydrogen level; heavy L 250 and L 300 angles above 30 mm need the most attention. Punching holes in thicker S355 legs may be restricted by the execution class; drilling or punch-and-ream avoids edge cracking. Galvanizing high-strength angles with punched holes and cold work warrants care to avoid liquid-metal-assisted cracking.
Delivery Condition, Inspection and Lead Time
| Item | Specify | Reason |
|---|---|---|
| Designation | L h × b × t, e.g. L 150 × 90 × 10 | Leg lengths alone do not fix thickness or mass |
| Delivery condition | +AR or +N where required | Not implied by the grade name |
| Impact test | Whether the 27 J at +20 °C result must be reported, and specimen size for thin legs | Angle legs run from 3 to 35 mm |
| Inspection document | EN 10204 3.1 for heat-specific results | Traceability to the delivered pieces |
| Dimensions | EN 10056-2 tolerances, lengths, cut list | Nominal values are not tolerances |
| Mass basis | Theoretical or weighed | Avoids invoicing disputes |
Lead time: typical delivery is about 35 days for mill orders, and sizes available from stock can ship in 1–3 days. Stock is confirmed size by size at enquiry; the angle tables on this page are reference geometry, not a stock list.
RFQ Checklist
- Full angle designation, quantity and lengths; equal and unequal sizes listed separately.
- EN 10025-2 S355JR, delivery condition and any chemistry options such as the galvanizing silicon range.
- Impact verification and EN 10204 document type.
- Processing: cutting, punching or drilling of legs, notching, galvanizing.
- Packing, marking and destination; whether stock sizes for 1–3 day dispatch are preferred over a mill order.
Other sections in the same grade: EN 10025-2 S355JR HEA and HEB beams, EN 10025-2 S355JR IPE beams and EN 10025-2 S355JR UPE and PFC channels. The hot-rolled steel angle range overview covers angles across grades, gussets and cleat plates are covered by EN 10025-2 S355JR steel plate, and the structural steel sections guide compares all section families.
The same equal and unequal angles in other EN 10025-2 grades: S235JR angles, S275JR angles, S355J2 angles.
Frequently Asked Questions
Which S355JR angles are Class 4 in compression?
Most thin-leg sizes. The common leg/10 proportion is already Class 4 because (b + h)/(2t) = 10 exceeds 11.5ε (about 9.3). 109 of 192 equal thicknesses and 21 of 32 unequal angles in the tables are Class 4.
How thick must an S355JR equal angle be to avoid Class 4?
Roughly t ≥ h/9.3 for legs up to 16 mm: L 100 × 100 needs 11 mm, L 150 × 150 needs 17 mm (at 345 MPa), and L 200 × 200 needs 22 mm.
Does CEV change for thick S355JR angles?
Yes. CEV is limited to 0.45% for t ≤ 30 mm and 0.47% for 30 < t ≤ 40 mm, which affects L 250 × 250 and L 300 × 300 at 31–35 mm.
Is S355JR the same as St 52-3?
No. St 52-3 required impact toughness at −20 °C, closer to S355J2. S355JR is tested at +20 °C.
Are S355JR angles suitable for transmission or telecom towers?
They are used in towers designed for enclosed or mild conditions, but tower codes and cold sites often require J0 or J2 impact quality. Check the project specification.
Does punching affect S355JR angle legs?
Punching cold-works the hole edge. Execution standards may limit full-size punching by thickness and execution class, or require reaming; galvanized members are particularly sensitive.
Why is the gross squash load not the resistance of a Class 4 angle?
For Class 4 sections only the effective area resists compression, and buckling about the weak axis reduces the resistance further. A·ReH is given only as a comparison value.
What lead time applies to S355JR angles?
About 35 days for mill orders and 1–3 days for stock sizes, confirmed per size at enquiry.
