EN 10025-2 S355JR UPE 200 and PFC 200 x 90 x 30 parallel-flange channel end views drawn to the same scale
Original generated illustration — UPE 200 and PFC 200 x 90 x 30 at the same scale; schematic only, not a dimensioned drawing, stock photograph or material certificate.

 

S355JR Parallel-Flange Channels: What the Order Covers

EN 10025-2 S355JR UPE and PFC channels give the highest strength among the common non-alloy structural grades with a +20 °C impact quality. Gangsteel supplies them for chords and diagonals of trusses, double-channel columns, bracing in industrial buildings, equipment skids and support frames where load, not deflection, decides the size. Order as “UPE 270, EN 10025-2 S355JR” or “PFC 300 × 90 × 41, EN 10025-2 S355JR”.

S355JR UPE and PFC channel specification
Item Value Note
Material EN 10025-2:2019 S355JR (1.0045) Impact quality 27 J at +20 °C
Section series UPE and PFC to EN 10365 Both have parallel inner flange faces; UPN (tapered flange) is a different series
Tolerances EN 10279 Channel-specific tolerances on dimensions, shape and mass
General delivery EN 10025-1 Testing, inspection documents, marking
Supply Gangsteel supplies EN 10025-2 S355JR UPE and PFC channels Sizes, quantities and stock confirmed per enquiry
Former designation St 52-3 was the closest DIN 17100 grade but was impact-tested at −20 °C; S355JR is not its direct equivalent Check old drawings carefully

UPE Channels in S355JR

UPE 80–400 in S355JR: geometry, yield band, elastic moduli, characteristic elastic moment and class in pure compression
Section h mm b mm tw mm tf mm kg/m ReH MPa Iy cm⁴ Wel,y cm³ Wel,z cm³ Wel,y·ReH kNm Class, axial
UPE 80 80 50 4.0 7.0 7.9 355 107 26.8 8 10 Class 1
UPE 100 100 55 4.5 7.5 9.8 355 207 41.4 11 15 Class 1
UPE 120 120 60 5.0 8.0 12.1 355 364 60.6 14 22 Class 1
UPE 140 140 65 5.0 9.0 14.5 355 600 85.6 18 30 Class 1
UPE 160 160 70 5.5 9.5 17.0 355 911 114 23 40 Class 1
UPE 180 180 75 5.5 10.5 19.7 355 1,350 150 29 53 Class 1
UPE 200 200 80 6.0 11.0 22.8 355 1,910 191 35 68 Class 1
UPE 220 220 85 6.5 12.0 26.6 355 2,680 244 43 87 Class 1
UPE 240 240 90 7.0 12.5 30.2 355 3,600 300 50 106 Class 1
UPE 270 270 95 7.5 13.5 35.2 355 5,250 389 61 138 Class 2
UPE 300 300 100 9.5 15.0 44.4 355 7,820 522 76 185 Class 1
UPE 330 330 105 11.0 16.0 53.2 355 11,000 667 90 237 Class 1
UPE 360 360 110 12.0 17.0 61.2 345 14,800 824 105 284 Class 1
UPE 400 400 115 13.5 18.0 72.2 345 21,000 1,050 123 362 Class 1

PFC Channels in S355JR

PFC 100 × 50 to 430 × 100 in S355JR: geometry, yield band, elastic moduli, characteristic elastic moment and class in pure compression
Section h mm b mm tw mm tf mm kg/m ReH MPa Iy cm⁴ Wel,y cm³ Wel,z cm³ Wel,y·ReH kNm Class, axial
PFC 100 × 50 × 10 100 50 5.0 8.5 10.2 355 208 41.5 10 15 Class 1
PFC 125 × 65 × 15 125 65 5.5 9.5 14.8 355 483 77.3 19 27 Class 1
PFC 150 × 75 × 18 150 75 5.5 10.0 17.9 355 861 115 27 41 Class 1
PFC 150 × 90 × 24 150 90 6.5 12.0 23.9 355 1,160 155 44 55 Class 1
PFC 180 × 75 × 20 180 75 6.0 10.5 20.3 355 1,370 152 29 54 Class 1
PFC 180 × 90 × 26 180 90 6.5 12.5 26.1 355 1,820 202 47 72 Class 1
PFC 200 × 75 × 23 200 75 6.0 12.5 23.4 355 1,960 196 34 70 Class 1
PFC 200 × 90 × 30 200 90 7.0 14.0 29.7 355 2,520 252 53 89 Class 1
PFC 230 × 75 × 26 230 75 6.5 12.5 25.7 355 2,750 239 35 85 Class 2
PFC 230 × 90 × 32 230 90 7.5 14.0 32.2 355 3,520 306 55 109 Class 1
PFC 260 × 75 × 28 260 75 7.0 12.0 27.6 355 3,620 278 34 99 Class 2
PFC 260 × 90 × 35 260 90 8.0 14.0 34.8 355 4,730 364 56 129 Class 1
PFC 300 × 90 × 41 300 90 9.0 15.5 41.4 355 7,220 481 63 171 Class 2
PFC 300 × 100 × 46 300 100 9.0 16.5 45.5 345 8,230 549 82 189 Class 1
PFC 380 × 100 × 54 380 100 9.5 17.5 54.0 345 15,000 791 89 273 Class 3
PFC 430 × 100 × 64 430 100 11.0 19.0 64.4 345 21,900 1,020 98 352 Class 3

The five sizes with flanges over 16 mm (UPE 360 (17.0 mm), UPE 400 (18.0 mm), PFC 300 × 100 × 46 (16.5 mm), PFC 380 × 100 × 54 (17.5 mm) and PFC 430 × 100 × 64 (19.0 mm)) are rated at 345 MPa; the rest at 355 MPa. At this strength ε falls to about 0.81, and the class picture changes more than for any lower grade: in pure compression UPE 270 becomes Class 2 (its web c/t of 28.4 exceeds 33ε = 26.8), PFC 230 × 75, 260 × 75 and 300 × 90 become Class 2, and PFC 380 × 100 and 430 × 100 become Class 3. For a Class 3 compression member the elastic, not plastic, resistance governs. In major-axis bending all sizes remain Class 1.

Wel,y·ReH is the characteristic elastic moment about the major axis using the S355JR yield band for that flange thickness. It is a cross-section value only, with no partial factor, no allowance for lateral-torsional buckling, and no allowance for the torsion that arises whenever a channel is loaded away from its shear centre, so it is not a safe working load. The axial class uses the EN 1993-1-1 limits for internal webs (33/38/42ε) and outstand flanges (9/10/14ε) with ε = √(235/ReH). Under pure major-axis bending every UPE and PFC size in this grade is Class 1. Confirm classification against the design code and national annex for the project.

S355JR Chemistry for Channel Sections

S355JR heat analysis, maximum mass % (all UPE and PFC flanges are below 30 mm)
Element Limit
C 0.24
Mn 1.60
Si 0.55
P 0.040
S 0.040
N 0.012 (waived with total Al ≥ 0.020% or reported N-binding elements)
Cu 0.55
CEV 0.45

S355JR allows up to 0.24% carbon and a CEV of 0.45%. The higher carbon ceiling compared with S355J2 (0.20%) is worth noting where weldability matters; actual mill heats are usually well below the limit, and an EN 10204 3.1 certificate shows the delivered analysis. Silicon is capped at 0.55%; request the galvanizing range separately if needed.

S355JR Tensile and Impact Requirements

S355JR properties for channel sections
Property tf ≤ 16 mm 16 mm < tf ≤ 40 mm
Minimum ReH 355 MPa 345 MPa
Rm 470–630 MPa 470–630 MPa
Minimum A (L0 = 5.65√S0) 22% 22%
Charpy V, minimum 27 J at +20 °C 27 J at +20 °C
Channels in this band UPE 80–330; PFC 100 × 50 to 300 × 90 UPE 360, UPE 400; PFC 300 × 100, 380 × 100, 430 × 100

Impact testing at +20 °C is appropriate for heated, enclosed structures. Where the structure is exposed or the fabrication specification sets a lower service temperature, S355J0 or S355J2 is the correct choice; S355JR certificates cannot be upgraded after delivery.

Designing with S355JR Channels

With 355 MPa yield, a channel has about 51% more elastic resistance than in S235JR, but its stiffness is unchanged. That makes S355JR attractive for members governed by strength, such as truss chords and bracing in tension, and less useful for long, lightly loaded rails sized by deflection. Approximate values: UPE 270 about 138 kNm (389 cm³ × 355 MPa), PFC 300 × 90 × 41 about 171 kNm.

In compression, single channels buckle in flexural-torsional modes because the section is singly symmetric. Back-to-back pairs connected by packs or batten plates and toe-to-toe built-up columns raise the minor-axis resistance and eliminate most of the twist. For the Class 2 and Class 3 PFC sizes above, check local buckling as well when they are used as struts.

S355JR Compared with Other Channel Grades

S355JR channels against other grades
Grade UPE 270 axial class PFC 380 × 100 × 54 axial class Impact quality
S235JR Class 1 Class 1 27 J at +20 °C
S275JR Class 1 Class 2 27 J at +20 °C
S355JR Class 2 Class 3 27 J at +20 °C
S355J2 Class 2 Class 3 27 J at −20 °C; C ≤ 0.20%

Fabrication: Connections, Welding and Coating

Weld S355JR channels to a qualified procedure; at CEV up to 0.45% the thicker PFC flanges and restrained joints may need preheat according to the combined thickness. Use matching-strength consumables. Punched holes in the webs of thin UPE sizes are acceptable only where the fabrication standard permits punching for the execution class. Parallel flanges avoid tapered washers, simplifying preloaded bolting.

Delivery Condition, Inspection and Lead Time

What to state on an S355JR channel order
Item Specify Reason
Series and size UPE 220 or PFC 230 × 90 × 32, never just “220 channel” UPE, PFC and UPN of similar depth differ in width, thickness and mass
Delivery condition +AR or +N where required Not implied by the grade name
Impact test Whether the 27 J at +20 °C result must be reported, and specimen size for thin flanges Channel flanges are 7–19 mm thick
Inspection document EN 10204 3.1 for heat-specific results Traceability to the delivered pieces
Dimensions EN 10279 tolerances, lengths, cut list Nominal values are not tolerances
Mass basis Theoretical or weighed Avoids invoicing disputes

Lead time: typical delivery is about 35 days for mill orders, and sizes available from stock can ship in 1–3 days. Stock is confirmed size by size at enquiry; the UPE and PFC tables on this page are reference geometry, not a stock list.

RFQ Checklist

  • Series and full designation (UPE or PFC), quantity and lengths.
  • EN 10025-2 S355JR, delivery condition and any chemistry options such as the galvanizing silicon range.
  • Impact verification and EN 10204 document type.
  • Processing: sawing, drilling or punching of web and flanges, blasting, priming, galvanizing.
  • Packing, marking and destination; whether stock sizes for 1–3 day dispatch are preferred over a mill order.

Primary members in the same grade are covered by EN 10025-2 S355JR HEA and HEB beams and EN 10025-2 S355JR IPE beams. The parallel flange channel size range and grade overview summarises PFC across grades, gusset and end plates are covered by EN 10025-2 S355JR steel plate, and the structural steel sections guide compares all section families.

The same UPE and PFC channels in other EN 10025-2 grades: S235JR channels, S275JR channels, S355J2 channels.

Frequently Asked Questions

Which S355JR channels are Class 3 in compression?

PFC 380 × 100 × 54 and PFC 430 × 100 × 64. At 345 MPa their webs exceed the Class 2 limit of 38ε but stay within 42ε, so elastic section properties apply when they carry axial compression.

Is S355JR equivalent to St 52-3?

Not exactly. St 52-3 required impact toughness at −20 °C, which corresponds more closely to S355J2. S355JR is tested at +20 °C only.

Which sizes are rated at 345 MPa?

UPE 360, UPE 400, and PFC 300 × 100 × 46, 380 × 100 × 54 and 430 × 100 × 64, because their flanges are thicker than 16 mm.

Does higher grade make a channel stiffer?

No. Elastic modulus is the same for all these steels, so deflection does not improve with S355JR. Choose a deeper or heavier section if stiffness governs.

Why use two S355JR channels instead of one larger channel?

A pair placed back-to-back or toe-to-toe is doubly symmetric or close to it, so the twisting caused by the offset shear centre disappears and the minor-axis buckling resistance can be tuned by the spacing.

Is S355JR suitable for outdoor structures?

With protection against corrosion it can be, if the design does not require toughness below +20 °C. Bridges, exposed frames in cold climates and dynamic structures usually call for S355J2 or better.

What chemistry limit matters most for welding S355JR channels?

The CEV maximum of 0.45%, together with the combined thickness at the joint, sets the preheat requirement. Carbon may be up to 0.24%; the certificate gives the actual value.

What is the delivery time for S355JR UPE and PFC?

Mill orders take about 35 days; stock sizes can ship within 1–3 days. Each size is confirmed at enquiry.

Other Products